![[Contents]](../images/toc_d.gif)
![[Index]](../images/index_d.gif)
![[Help]](../images/help_d.gif)
![[Retrace]](../images/retrace_d.gif)
![[Browse <]](../images/prev.gif)
![[Browse >]](../images/next.gif)
#ifndef LIBRARIES_CONFIGREGS_H
#define LIBRARIES_CONFIGREGS_H
/*
** $VER: configregs.h 36.13 (15.2.1991)
** Includes Release 44.1
**
** AutoConfig (tm) hardware register and bit definitions
**
** (C) Copyright 1985-1999 Amiga, Inc.
** All Rights Reserved
*/
#ifndef EXEC_TYPES_H
#include <exec/types.h>
#endif /* EXEC_TYPES_H */
/*
** AutoConfig (tm) boards each contain a 32 byte "ExpansionRom" area that is
** read by the system software at configuration time. Configuration of each
** board starts when the ConfigIn* signal is passed from the previous board
** (or from the system for the first board). Each board will present it's
** ExpansionRom structure at location $00E80000 to be read by the system.
** This file defines the appearance of the ExpansionRom area.
**
** Expansion boards are actually organized such that only one nybble per
** 16 bit word contains valid information. The low nybbles of each
** word are combined to fill the structure below. (This table is structured
** as LOGICAL information. This means that it never corresponds exactly
** with a physical implementation.)
**
** The ExpansionRom space is further split into two regions: The first 16
** bytes are read-only. Except for the er_type field, this area is inverted
** by the system software when read in. The second 16 bytes contain the
** control portion, where all read/write registers are located.
**
** The system builds one "ConfigDev" structure for each board found. The
** list of boards can be examined using the expansion.library/FindConfigDev
** function.
**
** A special "hacker" Manufacturer ID number is reserved for test use:
** 2011 ($7DB). When inverted this will look like $F824.
*/
struct ExpansionRom { /* -First 16 bytes of the expansion ROM */
UBYTE er_Type; /* Board type, size and flags */
UBYTE er_Product; /* Product number, assigned by manufacturer */
UBYTE er_Flags; /* Flags */
UBYTE er_Reserved03; /* Must be zero ($ff inverted) */
UWORD er_Manufacturer; /* Unique ID,ASSIGNED BY AMIGA, INC.! */
ULONG er_SerialNumber; /* Available for use by manufacturer */
UWORD er_InitDiagVec; /* Offset to optional "DiagArea" structure */
UBYTE er_Reserved0c;
UBYTE er_Reserved0d;
UBYTE er_Reserved0e;
UBYTE er_Reserved0f;
};
/*
** Note that use of the ec_BaseAddress register is tricky. The system
** will actually write twice. First the low order nybble is written
** to the ec_BaseAddress register+2 (D15-D12). Then the entire byte is
** written to ec_BaseAddress (D15-D8). This allows writing of a byte-wide
** address to nybble size registers.
*/
struct ExpansionControl { /* -Second 16 bytes of the expansion ROM */
UBYTE ec_Interrupt; /* Optional interrupt control register */
UBYTE ec_Z3_HighBase; /* Zorro III : Config address bits 24-31 */
UBYTE ec_BaseAddress; /* Zorro II/III: Config address bits 16-23 */
UBYTE ec_Shutup; /* The system writes here to shut up a board */
UBYTE ec_Reserved14;
UBYTE ec_Reserved15;
UBYTE ec_Reserved16;
UBYTE ec_Reserved17;
UBYTE ec_Reserved18;
UBYTE ec_Reserved19;
UBYTE ec_Reserved1a;
UBYTE ec_Reserved1b;
UBYTE ec_Reserved1c;
UBYTE ec_Reserved1d;
UBYTE ec_Reserved1e;
UBYTE ec_Reserved1f;
};
/*
** many of the constants below consist of a triplet of equivalent
** definitions: xxMASK is a bit mask of those bits that matter.
** xxBIT is the starting bit number of the field. xxSIZE is the
** number of bits that make up the definition. This method is
** used when the field is larger than one bit.
**
** If the field is only one bit wide then the xxB_xx and xxF_xx convention
** is used (xxB_xx is the bit number, and xxF_xx is mask of the bit).
*/
/* manifest constants */
#define E_SLOTSIZE 0x10000
#define E_SLOTMASK 0xffff
#define E_SLOTSHIFT 16
/* these define the free regions of Zorro memory space.
** THESE MAY WELL CHANGE FOR FUTURE PRODUCTS!
*/
#define E_EXPANSIONBASE 0x00e80000 /* Zorro II config address */
#define EZ3_EXPANSIONBASE 0xff000000 /* Zorro III config address */
#define E_EXPANSIONSIZE 0x00080000 /* Zorro II I/O type cards */
#define E_EXPANSIONSLOTS 8
#define E_MEMORYBASE 0x00200000 /* Zorro II 8MB space */
#define E_MEMORYSIZE 0x00800000
#define E_MEMORYSLOTS 128
#define EZ3_CONFIGAREA 0x40000000 /* Zorro III space */
#define EZ3_CONFIGAREAEND 0x7FFFFFFF /* Zorro III space */
#define EZ3_SIZEGRANULARITY 0x00080000 /* 512K increments */
/**** er_Type definitions (ttldcmmm) ***************************************/
/* er_Type board type bits -- the OS ignores "old style" boards */
#define ERT_TYPEMASK 0xc0 /* Bits 7-6 */
#define ERT_TYPEBIT 6
#define ERT_TYPESIZE 2
#define ERT_NEWBOARD 0xc0
#define ERT_ZORROII ERT_NEWBOARD
#define ERT_ZORROIII 0x80
/* other bits defined in er_Type */
#define ERTB_MEMLIST 5 /* Link RAM into free memory list */
#define ERTB_DIAGVALID 4 /* ROM vector is valid */
#define ERTB_CHAINEDCONFIG 3 /* Next config is part of the same card */
#define ERTF_MEMLIST (1<<5)
#define ERTF_DIAGVALID (1<<4)
#define ERTF_CHAINEDCONFIG (1<<3)
/* er_Type field memory size bits */
#define ERT_MEMMASK 0x07 /* Bits 2-0 */
#define ERT_MEMBIT 0
#define ERT_MEMSIZE 3
/**** er_Flags byte -- for those things that didn't fit into the type byte ****/
/**** the hardware stores this byte in inverted form ****/
#define ERFF_MEMSPACE (1<<7) /* Wants to be in 8 meg space. */
#define ERFB_MEMSPACE 7 /* (NOT IMPLEMENTED) */
#define ERFF_NOSHUTUP (1<<6) /* Board can't be shut up */
#define ERFB_NOSHUTUP 6
#define ERFF_EXTENDED (1<<5) /* Zorro III: Use extended size table */
#define ERFB_EXTENDED 5 /* for bits 0-2 of er_Type */
/* Zorro II : Must be 0 */
#define ERFF_ZORRO_III (1<<4) /* Zorro III: must be 1 */
#define ERFB_ZORRO_III 4 /* Zorro II : must be 0 */
#define ERT_Z3_SSMASK 0x0F /* Bits 3-0. Zorro III Sub-Size. How */
#define ERT_Z3_SSBIT 0 /* much space the card actually uses */
#define ERT_Z3_SSSIZE 4 /* (regardless of config granularity) */
/* Zorro II : must be 0 */
/* ec_Interrupt register (unused) ********************************************/
#define ECIB_INTENA 1
#define ECIB_RESET 3
#define ECIB_INT2PEND 4
#define ECIB_INT6PEND 5
#define ECIB_INT7PEND 6
#define ECIB_INTERRUPTING 7
#define ECIF_INTENA (1<<1)
#define ECIF_RESET (1<<3)
#define ECIF_INT2PEND (1<<4)
#define ECIF_INT6PEND (1<<5)
#define ECIF_INT7PEND (1<<6)
#define ECIF_INTERRUPTING (1<<7)
/* figure out amount of memory needed by this box/board */
#define ERT_MEMNEEDED(t) \
(((t)&ERT_MEMMASK)? 0x10000 << (((t)&ERT_MEMMASK) -1) : 0x800000 )
/* same as ERT_MEMNEEDED, but return number of slots */
#define ERT_SLOTSNEEDED(t) \
(((t)&ERT_MEMMASK)? 1 << (((t)&ERT_MEMMASK)-1) : 0x80 )
/* convert a expansion slot number into a memory address */
#define EC_MEMADDR(slot) ((slot) << (E_SLOTSHIFT) )
/* a kludge to get the byte offset of a structure */
#define EROFFSET(er) ((int)&((struct ExpansionRom *)0)->er)
#define ECOFFSET(ec) \
(sizeof(struct ExpansionRom)+((int)&((struct ExpansionControl *)0)->ec))
/***************************************************************************
**
** these are the specifications for the diagnostic area. If the Diagnostic
** Address Valid bit is set in the Board Type byte (the first byte in
** expansion space) then the Diag Init vector contains a valid offset.
**
** The Diag Init vector is actually a word offset from the base of the
** board. The resulting address points to the base of the DiagArea
** structure. The structure may be physically implemented either four,
** eight, or sixteen bits wide. The code will be copied out into
** ram first before being called.
**
** The da_Size field, and both code offsets (da_DiagPoint and da_BootPoint)
** are offsets from the diag area AFTER it has been copied into ram, and
** "de-nibbleized" (if needed). (In other words, the size is the size of
** the actual information, not how much address space is required to
** store it.)
**
** All bits are encoded with uninverted logic (e.g. 5 volts on the bus
** is a logic one).
**
** If your board is to make use of the boot facility then it must leave
** its config area available even after it has been configured. Your
** boot vector will be called AFTER your board's final address has been
** set.
**
****************************************************************************/
struct DiagArea {
UBYTE da_Config; /* see below for definitions */
UBYTE da_Flags; /* see below for definitions */
UWORD da_Size; /* the size (in bytes) of the total diag area */
UWORD da_DiagPoint; /* where to start for diagnostics, or zero */
UWORD da_BootPoint; /* where to start for booting */
UWORD da_Name; /* offset in diag area where a string */
/* identifier can be found (or zero if no */
/* identifier is present). */
UWORD da_Reserved01; /* two words of reserved data. must be zero. */
UWORD da_Reserved02;
};
/* da_Config definitions */
/*
** DAC_BYTEWIDE can be simulated using DAC_NIBBLEWIDE.
*/
#define DAC_BUSWIDTH 0xC0 /* two bits for bus width */
#define DAC_NIBBLEWIDE 0x00
#define DAC_BYTEWIDE 0x40 /* BUG: Will not work under V34 Kickstart! */
#define DAC_WORDWIDE 0x80
#define DAC_BOOTTIME 0x30 /* two bits for when to boot */
#define DAC_NEVER 0x00 /* obvious */
#define DAC_CONFIGTIME 0x10 /* call da_BootPoint when first configing */
/* the device */
#define DAC_BINDTIME 0x20 /* run when binding drivers to boards */
/*
**
** These are the calling conventions for the diagnostic callback
** (from da_DiagPoint):
**
** A7 -- points to at least 2K of stack
** A6 -- ExecBase
** A5 -- ExpansionBase
** A3 -- your board's ConfigDev structure
** A2 -- Base of diag/init area that was copied
** A0 -- Base of your board
**
** Your board must return a value in D0. If this value is NULL, then
** the diag/init area that was copied in will be returned to the free
** memory pool.
*/
#endif /* LIBRARIES_CONFIGREGS_H */