OpenWrt – Rev 1

Subversion Repositories:
Rev:
/dts-v1/;

#include "mt7628an.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
        compatible = "d-team,pbr-d1", "mediatek,mt7628an-soc";
        model = "PBR-D1";

        aliases {
                led-boot = &led_power;
                led-failsafe = &led_power;
                led-running = &led_power;
                led-upgrade = &led_power;
        };

        chosen {
                bootargs = "console=ttyS0,115200";
        };

        aliases {
                serial0 = &uart2;
        };

        memory@0 {
                device_type = "memory";
                reg = <0x0 0x8000000>;
        };

        leds {
                compatible = "gpio-leds";

                usb {
                        label = "pbr-d1:orange:usb";
                        gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
                        trigger-sources = <&ohci_port1>, <&ehci_port1>;
                        linux,default-trigger = "usbport";
                };

                led_power: power {
                        label = "pbr-d1:orange:power";
                        gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
                        default-state = "on";
                };
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <20>;

                reset {
                        label = "reset";
                        gpios = <&gpio1 38 GPIO_ACTIVE_LOW>;
                        linux,code = <KEY_RESTART>;
                };
        };

        wgpio: gpio-wifi {
                compatible = "mediatek,gpio-wifi";
                #address-cells = <1>;
                #size-cells = <0>;
                gpio-controller;
                #gpio-cells = <2>;
        };
};

&pinctrl {
        state_default: pinctrl0 {
                gpio {
                        ralink,group = "gpio";
                        ralink,function = "gpio";
                };

                i2c {
                        ralink,group = "i2c";
                        ralink,function = "gpio";
                };

                i2s {
                        ralink,group = "i2s";
                        ralink,function = "gpio";
                };

                spis {
                        ralink,group = "spis";
                        ralink,function = "gpio";
                };

                wdt {
                        ralink,group = "wdt";
                        ralink,function = "gpio";
                };
        };
};

&spi0 {
        status = "okay";

        pinctrl-names = "default";
        pinctrl-0 = <&spi_pins>, <&spi_cs1_pins>;

        m25p80@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <40000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x0 0x30000>;
                                read-only;
                        };

                        partition@30000 {
                                label = "u-boot-env";
                                reg = <0x30000 0x10000>;
                        };

                        factory: partition@40000 {
                                label = "factory";
                                reg = <0x40000 0x10000>;
                                read-only;
                        };

                        partition@50000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x50000 0x0fb0000>;
                        };
                };
        };

        spidev@1 {
                #address-cells = <1>;
                #size-cells = <1>;
                compatible = "linux,spidev";
                reg = <1>;
                spi-max-frequency = <40000000>;
        };
};

&i2c {
        status = "okay";
};

&uart1 {
        status = "okay";
};

&uart2 {
        status = "okay";
};

&pwm {
        status = "okay";
};

&ethernet {
        mtd-mac-address = <&factory 0x28>;
};

&sdhci {
        status = "okay";
        mediatek,cd-high;
};