OpenWrt – Rev 1

Subversion Repositories:
Rev:
/dts-v1/;

#include "rt3883.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
        compatible = "omnima,hpm", "ralink,rt3883-soc";
        model = "Omnima HPM";

        aliases {
                led-boot = &led_status;
                led-failsafe = &led_status;
                led-running = &led_status;
                led-upgrade = &led_status;
        };

        chosen {
                bootargs = "console=ttyS0,115200";
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <100>;

                reset {
                        label = "reset";
                        gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
                        linux,code = <KEY_RESTART>;
                };
        };

        leds {
                compatible = "gpio-leds";

                power {
                        label = "hpm:orange:power";
                        gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
                        default-state = "on";
                };

                led_status: status {
                        label = "hpm:green:status";
                        gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
                        default-state = "on";
                };

                eth {
                        label = "hpm:green:eth";
                        gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
                };

                eth2 {
                        label = "hpm:red:eth";
                        gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
                };

                wifi {
                        label = "hpm:green:wifi";
                        gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
                };

                wifi2 {
                        label = "hpm:red:wifi";
                        gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
                };
        };

        gpio_export {
                compatible = "gpio-export";
                #size-cells = <0>;
                /* gpio 12 and 13 handle the OC input */

                usb0 {
                        gpio-export,name = "usb0";
                        gpio-export,output = <1>;
                        gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
                };

                usb1 {
                        gpio-export,name = "usb1";
                        gpio-export,output = <1>;
                        gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
                };
        };
};

&spi0 {
        status = "okay";

        m25p80@0 {
                compatible = "jedec,spi-nor";
                spi-max-frequency = <25000000>;
                reg = <0>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                reg = <0x0 0x0030000>;
                                label = "u-boot";
                                read-only;
                        };

                        partition@30000 {
                                reg = <0x00030000 0x00010000>;
                                label = "config";
                                read-only;
                        };

                        factory: partition@40000 {
                                reg = <0x00040000 0x00010000>;
                                label = "factory";
                                read-only;
                        };

                        partition@50000 {
                                compatible = "denx,uimage";
                                reg = <0x00050000 0x00fb0000>;
                                label = "firmware";
                        };
                };
        };
};

&pinctrl {
        state_default: pinctrl0 {
                gpio {
                        ralink,group = "i2c", "jtag", "uartf";
                        ralink,function = "gpio";
                };
        };
};

&ethernet {
        phy-handle = <&phy0>;
        phy-mode = "rgmii";
        mtd-mac-address = <&factory 0x28>;

        mdio-bus {
                status = "okay";

                phy0: ethernet-phy@4 {
                        reg = <4>;
                };
        };
};

&wmac {
        ralink,mtd-eeprom = <&factory 0>;
};

&ehci {
        status = "okay";
};

&ohci {
        status = "okay";
};