OpenWrt – Rev 1
?pathlinks?
From d41d41bfcbd8ad4bcbb1b433f7d5c3b613c58419 Mon Sep 17 00:00:00 2001
From: Sean Wang <sean.wang@mediatek.com>
Date: Mon, 22 Jan 2018 16:58:36 +0800
Subject: [PATCH 223/224] arm64: dts: mt7622: add mmc related device nodes
add mmc device nodes and proper setup for used pins
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jimin Wang <jimin.wang@mediatek.com>
---
arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts | 106 +++++++++++++++++++++++++++
arch/arm64/boot/dts/mediatek/mt7622.dtsi | 20 +++++
2 files changed, 126 insertions(+)
--- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
#include "mt7622.dtsi"
#include "mt6380.dtsi"
@@ -53,6 +54,14 @@
reg = <0 0x40000000 0 0x3F000000>;
};
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
@@ -89,6 +98,23 @@
function = "emmc", "emmc_rst";
groups = "emmc";
};
+
+ /* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
+ * "NRB","NCLE" pins are used as DAT0,DAT1,DAT2,DAT3,DAT4,
+ * DAT5,DAT6,DAT7,CMD,CLK for eMMC respectively
+ */
+ conf-cmd-dat {
+ pins = "NDL0", "NDL1", "NDL2",
+ "NDL3", "NDL4", "NDL5",
+ "NDL6", "NDL7", "NRB";
+ input-enable;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "NCLE";
+ bias-pull-down;
+ };
};
emmc_pins_uhs: emmc-pins-uhs {
@@ -96,6 +122,21 @@
function = "emmc";
groups = "emmc";
};
+
+ conf-cmd-dat {
+ pins = "NDL0", "NDL1", "NDL2",
+ "NDL3", "NDL4", "NDL5",
+ "NDL6", "NDL7", "NRB";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "NCLE";
+ drive-strength = <4>;
+ bias-pull-down;
+ };
};
eth_pins: eth-pins {
@@ -194,6 +235,27 @@
function = "sd";
groups = "sd_0";
};
+
+ /* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
+ * "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
+ * DAT2, DAT3, CMD, CLK for SD respectively.
+ */
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ conf-clk {
+ pins = "I2S3_OUT";
+ drive-strength = <12>;
+ bias-pull-down;
+ };
+ conf-cd {
+ pins = "TXD3";
+ bias-pull-up;
+ };
};
sd0_pins_uhs: sd0-pins-uhs {
@@ -201,6 +263,18 @@
function = "sd";
groups = "sd_0";
};
+
+ conf-cmd-data {
+ pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
+ "I2S2_IN","I2S4_OUT";
+ input-enable;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "I2S3_OUT";
+ bias-pull-down;
+ };
};
/* Serial NAND is shared pin with SPI-NOR */
@@ -311,6 +385,38 @@
status = "okay";
};
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&emmc_pins_default>;
+ pinctrl-1 = <&emmc_pins_uhs>;
+ status = "okay";
+ bus-width = <8>;
+ max-frequency = <50000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+ non-removable;
+};
+
+&mmc1 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&sd0_pins_default>;
+ pinctrl-1 = <&sd0_pins_uhs>;
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <50000000>;
+ cap-sd-highspeed;
+ r_smpl = <1>;
+ cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_3p3v>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
+};
+
&nandc {
pinctrl-names = "default";
pinctrl-0 = <¶llel_nand_pins>;
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -527,6 +527,26 @@
status = "disabled";
};
+ mmc0: mmc@11230000 {
+ compatible = "mediatek,mt7622-mmc";
+ reg = <0 0x11230000 0 0x1000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_MSDC30_0_PD>,
+ <&topckgen CLK_TOP_MSDC50_0_SEL>;
+ clock-names = "source", "hclk";
+ status = "disabled";
+ };
+
+ mmc1: mmc@11240000 {
+ compatible = "mediatek,mt7622-mmc";
+ reg = <0 0x11240000 0 0x1000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_MSDC30_1_PD>,
+ <&topckgen CLK_TOP_AXI_SEL>;
+ clock-names = "source", "hclk";
+ status = "disabled";
+ };
+
ssusbsys: ssusbsys@1a000000 {
compatible = "mediatek,mt7622-ssusbsys",
"syscon";