OpenWrt – Rev 1
?pathlinks?
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "AVM FRITZ!Box 4040";
compatible = "avm,fritzbox-4040";
aliases {
led-boot = &power;
led-failsafe = &flash;
led-running = &power;
led-upgrade = &flash;
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2@60f8800 {
status = "okay";
};
usb3@8af8800 {
status = "okay";
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
qca8075: ess-switch@c000000 {
status = "okay";
#gpio-cells = <2>;
gpio-controller;
enable-usb-power {
gpio-hog;
line-name = "enable USB3 power";
gpios = <7 GPIO_ACTIVE_HIGH>;
output-high;
};
};
edma@c080000 {
status = "okay";
};
};
keys {
compatible = "gpio-keys";
wlan {
label = "wlan";
gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
wps {
label = "wps";
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
switch-leds {
compatible = "gpio-leds";
wlan {
label = "fritz4040:green:wlan";
gpios = <&qca8075 1 GPIO_ACTIVE_HIGH>;
};
panic: info_red {
label = "fritz4040:red:info";
gpios = <&qca8075 3 GPIO_ACTIVE_HIGH>;
panic-indicator;
};
wan {
label = "fritz4040:green:wan";
gpios = <&qca8075 5 GPIO_ACTIVE_HIGH>;
};
power: power {
label = "fritz4040:green:power";
gpios = <&qca8075 11 GPIO_ACTIVE_HIGH>;
};
lan {
label = "fritz4040:green:lan";
gpios = <&qca8075 13 GPIO_ACTIVE_HIGH>;
};
flash: info_amber {
label = "fritz4040:amber:info";
gpios = <&qca8075 15 GPIO_ACTIVE_HIGH>;
};
};
};
&tlmm {
serial_pins: serial_pinmux {
mux {
pins = "gpio60", "gpio61";
function = "blsp_uart0";
bias-disable;
};
};
spi_0_pins: spi_0_pinmux {
mux {
function = "blsp_spi0";
pins = "gpio55", "gpio56", "gpio57";
drive-strength = <12>;
bias-disable;
};
mux_cs {
function = "gpio";
pins = "gpio54";
drive-strength = <2>;
bias-disable;
output-high;
};
};
};
&cryptobam {
status = "okay";
};
&blsp_dma {
status = "okay";
};
&blsp1_spi1 { /* BLSP1 QUP1 */
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "okay";
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
status = "okay";
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition0@0 {
label = "SBL1";
reg = <0x00000000 0x00040000>;
read-only;
};
partition1@40000 {
label = "MIBIB";
reg = <0x00040000 0x00020000>;
read-only;
};
partition2@60000 {
label = "QSEE";
reg = <0x00060000 0x00060000>;
read-only;
};
partition3@c0000 {
label = "CDT";
reg = <0x000c0000 0x00010000>;
read-only;
};
partition4@d0000 {
label = "DDRPARAMS";
reg = <0x000d0000 0x00010000>;
read-only;
};
partition5@e0000 {
label = "APPSBLENV"; /* uboot env - empty */
reg = <0x000e0000 0x00010000>;
read-only;
};
partition6@f0000 {
label = "urlader"; /* APPSBL */
reg = <0x000f0000 0x0002dc000>;
read-only;
};
partition7@11dc00 {
/* make a backup of this partition! */
label = "urlader_config";
reg = <0x0011dc00 0x00002400>;
read-only;
};
partition8@120000 {
label = "tffs1";
reg = <0x00120000 0x00080000>;
read-only;
};
partition9@1a0000 {
label = "tffs2";
reg = <0x001a0000 0x00080000>;
read-only;
};
partition10@220000 {
label = "uboot";
reg = <0x00220000 0x00080000>;
read-only;
};
partition11@2A0000 {
compatible = "denx,fit";
label = "firmware";
reg = <0x002a0000 0x01c60000>;
};
partition12@1f00000 {
label = "jffs2";
reg = <0x01f00000 0x00100000>;
};
};
};
};
&blsp1_uart1 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "okay";
};
&usb3_ss_phy {
status = "okay";
};
&usb3_hs_phy {
status = "okay";
};
&usb2_hs_phy {
status = "okay";
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "AVM-FRITZBox-4040";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "AVM-FRITZBox-4040";
};