OpenWrt – Rev 1
?pathlinks?
// SPDX-License-Identifier: GPL-2.0+ OR MIT
/dts-v1/;
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "ASUS Lyra MAP-AC2200";
compatible = "asus,map-ac2200";
aliases {
led-boot = &led_blue0;
led-failsafe = &led_red0;
led-running = &led_blue0;
led-upgrade = &led_red0;
};
soc {
mdio@90000 {
status = "okay";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2@60f8800 {
status = "okay";
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
};
&nand {
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
status = "okay";
nand@0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "SBL1";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
label = "MIBIB";
reg = <0x80000 0x80000>;
read-only;
};
partition@100000 {
label = "QSEE";
reg = <0x100000 0x100000>;
read-only;
};
partition@200000 {
label = "CDT";
reg = <0x200000 0x80000>;
read-only;
};
partition@280000 {
label = "APPSBL";
reg = <0x280000 0x140000>;
read-only;
};
partition@3c0000 {
label = "APPSBLENV";
reg = <0x3c0000 0x40000>;
read-only;
};
partition@400000 {
label = "ubi";
reg = <0x400000 0x7c00000>;
};
};
};
};
&tlmm {
i2c_0_pins: i2c_0_pinmux {
pinmux {
function = "blsp_i2c0";
pins = "gpio20", "gpio21";
drive-strength = <16>;
bias-disable;
};
};
serial_pins: serial_pinmux {
mux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
};
nand_pins: nand_pins {
pullups {
pins = "gpio52", "gpio53", "gpio58",
"gpio59";
function = "qpic";
bias-pull-up;
};
pulldowns {
pins = "gpio54", "gpio55", "gpio56",
"gpio57", "gpio60", "gpio61",
"gpio62", "gpio63", "gpio64",
"gpio65", "gpio66", "gpio67",
"gpio68", "gpio69";
function = "qpic";
bias-pull-down;
};
};
};
&cryptobam {
status = "okay";
};
&blsp_dma {
status = "okay";
};
&qpic_bam {
status = "okay";
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "ASUS-MAP-AC2200";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "ASUS-MAP-AC2200";
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
bridge@0,0 {
reg = <0x00000000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
wifi2: wifi@1,0 {
compatible = "qcom,ath10k";
status = "okay";
reg = <0x00010000 0 0 0 0>;
qcom,ath10k-calibration-variant = "ASUS-MAP-AC2200";
};
};
};
&usb2_hs_phy {
/* Bluetooth module attached via USB */
status = "okay";
};
&blsp1_i2c3 {
pinctrl-0 = <&i2c_0_pins>;
pinctrl-names = "default";
status = "okay";
led-controller@32 {
/* 9-channel RGB LED controller */
compatible = "national,lp5523";
reg = <0x32>;
clock-mode = [01];
led_blue0: blue0 {
chan-name = "blue0";
label = "map-ac2200:blue:chan0";
led-cur = [fa];
max-cur = [ff];
};
blue1 {
chan-name = "blue1";
label = "map-ac2200:blue:chan1";
led-cur = [fa];
max-cur = [ff];
};
blue2 {
chan-name = "blue2";
label = "map-ac2200:blue:chan2";
led-cur = [fa];
max-cur = [ff];
};
led_green0: green0 {
chan-name = "green0";
label = "map-ac2200:green:chan0";
led-cur = [fa];
max-cur = [ff];
};
green1 {
chan-name = "green1";
label = "map-ac2200:green:chan1";
led-cur = [fa];
max-cur = [ff];
};
green2 {
chan-name = "green2";
label = "map-ac2200:green:chan2";
led-cur = [fa];
max-cur = [ff];
};
led_red0: red0 {
chan-name = "red0";
label = "map-ac2200:red:chan0";
led-cur = [fa];
max-cur = [ff];
};
red1 {
chan-name = "red1";
label = "map-ac2200:red:chan1";
led-cur = [fa];
max-cur = [ff];
};
red2 {
chan-name = "red2";
label = "map-ac2200:red:chan2";
led-cur = [fa];
max-cur = [ff];
};
};
};
&blsp1_uart1 {
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
status = "okay";
};