OpenWrt – Rev 1
?pathlinks?
From f0674df220f3da81c173025636a904b395cf8f8b Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@linaro.org>
Date: Sun, 19 Nov 2017 10:46:16 +0100
Subject: [PATCH 12/31] ARM: dts: Add ethernet PHYs to the a bunch of Geminis
These Gemini boards have Ethernet PHY on GPIO bit-banged
MDIO, clearly defined in the corresponding OpenWRT
ethernet patches since ages. Add them in accordance with
the OpenWRT patch so we can use them when we add ethernet
support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/gemini-nas4220b.dts | 13 +++++++++++++
arch/arm/boot/dts/gemini-wbd111.dts | 13 +++++++++++++
arch/arm/boot/dts/gemini-wbd222.dts | 18 ++++++++++++++++++
4 files changed, 57 insertions(+)
--- a/arch/arm/boot/dts/gemini-nas4220b.dts
+++ b/arch/arm/boot/dts/gemini-nas4220b.dts
@@ -64,6 +64,19 @@
};
};
+ mdio0: ethernet-phy {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
soc {
flash@30000000 {
status = "okay";
--- a/arch/arm/boot/dts/gemini-wbd111.dts
+++ b/arch/arm/boot/dts/gemini-wbd111.dts
@@ -69,6 +69,19 @@
};
};
+ mdio0: ethernet-phy {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
soc {
flash@30000000 {
status = "okay";
--- a/arch/arm/boot/dts/gemini-wbd222.dts
+++ b/arch/arm/boot/dts/gemini-wbd222.dts
@@ -69,6 +69,24 @@
};
};
+ mdio0: ethernet-phy {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@3 {
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
+
soc {
flash@30000000 {
status = "okay";