OpenWrt – Rev 1
?pathlinks?
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca956x.dtsi"
/ {
compatible = "tplink,archer-c7-v4", "qca,qca9563";
model = "TP-Link Archer C7 v4";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &system;
led-failsafe = &system;
led-running = &system;
led-upgrade = &system;
};
led_spi {
compatible = "spi-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpio-sck = <&gpio 15 GPIO_ACTIVE_HIGH>; // 74HC595 SRCLK (Serial Clock)
gpio-mosi = <&gpio 14 GPIO_ACTIVE_HIGH>; // 74HC595 SER (Serial)
cs-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; // 74HC595 RCLK (Register Clock)
num-chipselects = <1>;
led_gpio: led_gpio@0 {
compatible = "fairchild,74hc595";
reg = <0>;
gpio-controller;
#gpio-cells = <2>;
registers-number = <1>;
spi-max-frequency = <10000000>;
};
};
gpio-export {
compatible = "gpio-export";
gpio_shift_register_oe {
gpio-export,name = "tp-link:oe:sr";
gpio-export,output = <0>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>; // 74HC595 /OE (Output Enable)
};
gpio_shift_register_reset {
gpio-export,name = "tp-link:reset:sr";
gpio-export,output = <1>;
gpios = <&gpio 21 GPIO_ACTIVE_LOW>; // 74HC595 /SRCLR (Serial Clear)
};
};
leds {
compatible = "gpio-leds";
system: system {
label = "tp-link:green:system";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
default-state = "on";
};
usb1 {
label = "tp-link:green:usb1";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
trigger-sources = <&hub_port1>;
linux,default-trigger = "usbport";
};
usb2 {
label = "tp-link:green:usb2";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
trigger-sources = <&hub_port0>;
linux,default-trigger = "usbport";
};
wlan5g {
label = "tp-link:green:wlan5g";
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wlan2g {
label = "tp-link:green:wlan2g";
gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
wan {
label = "tp-link:green:wan";
gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
};
wan_fail {
label = "tp-link:orange:wan";
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
};
lan1 {
label = "tp-link:green:lan1";
gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
};
lan2 {
label = "tp-link:green:lan2";
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
};
lan3 {
label = "tp-link:green:lan3";
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
};
lan4 {
label = "tp-link:green:lan4";
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
};
wps {
label = "tp-link:green:wps";
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
label = "WPS button";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&pcie {
status = "okay";
};
&uart {
status = "okay";
};
&gpio {
status = "okay";
};
&usb_phy0 {
status = "okay";
};
&usb0 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
hub_port0: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&usb_phy1 {
status = "okay";
};
&usb1 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
hub_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "factory-uboot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
label = "u-boot";
reg = <0x020000 0x020000>;
read-only;
};
partition@40000 {
label = "firmware";
reg = <0x040000 0xec0000>;
compatible = "denx,uimage";
};
info: partition@f00000 {
label = "config";
reg = <0xf00000 0x0f0000>;
read-only;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy-mask = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "sgmii";
qca,ar8327-initvals = <
0x04 0x80080080 /* PORT0 PAD MODE CTRL */
0x7c 0x0000007e /* PORT0_STATUS */
0x94 0x00000200 /* PORT6_STATUS */
>;
};
};
ð0 {
status = "okay";
pll-data = <0x03000101 0x00000101 0x00001919>;
phy-mode = "sgmii";
mtd-mac-address = <&info 0x8>;
phy-handle = <&phy0>;
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&info 0x8>;
};