OpenWrt – Rev 1

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca956x.dtsi"

/ {
        model = "Phicomm K2T";
        compatible = "phicomm,k2t", "qca,qca9563";

        aliases {
                led-boot = &status_red;
                led-failsafe = &status_red;
                led-running = &status_red;
                led-upgrade = &status_red;
        };

        chosen {
                bootargs = "console=ttyS0,115200n8";
        };

        leds {
                compatible = "gpio-leds";

                status_blue {
                        label = "phicomm:blue:status";
                        gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
                };

                status_red: status_red {
                        label = "phicomm:red:status";
                        gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
                };

                status_yellow {
                        label = "phicomm:yellow:status";
                        gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
                };
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <20>;

                reset {
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
                        debounce-interval = <60>;
                };
        };
};

&uart {
        status = "okay";
};

&gpio {
        status = "okay";
};

&pcie {
        status = "okay";
};

&spi {
        num-cs = <1>;

        status = "okay";

        flash@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <25000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x30000>;
                                read-only;
                        };

                        partition@30000 {
                                label = "config";
                                reg = <0x030000 0x10000>;
                                read-only;
                        };

                        partition@40000 {
                                label = "permanent";
                                reg = <0x040000 0x50000>;
                                read-only;
                        };

                        partition@90000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x090000 0xf60000>;
                        };

                        art: partition@ff0000 {
                                label = "art";
                                reg = <0xff0000 0x010000>;
                                read-only;
                        };
                };
        };
};

&mdio0 {
        status = "okay";

        phy-mask = <0>;

        phy0: ethernet-phy@0 {
                reg = <0>;
                phy-mode = "sgmii";

                qca,ar8327-initvals = <
                        0x04 0x00080080 /* PORT0 PAD MODE CTRL */
                        0x10 0x81000080 /* POWER_ON_STRIP */
                        0x50 0xcc35cc35 /* LED_CTRL0 */
                        0x54 0xcb37cb37 /* LED_CTRL1 */
                        0x58 0x00000000 /* LED_CTRL2 */
                        0x5c 0x00f3cf00 /* LED_CTRL3 */
                        0x7c 0x0000007e /* PORT0_STATUS */
                        >;
        };
};

&eth0 {
        status = "okay";

        pll-data = <0x03000101 0x00000101 0x00001919>;

        phy-mode = "sgmii";
        phy-handle = <&phy0>;
};

&wmac {
        status = "okay";
        mtd-cal-data = <&art 0x1000>;
};