OpenWrt – Rev 1

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca956x.dtsi"

/ {
        compatible = "glinet,gl-ar750s", "qca,qca9563";
        model = "GL.iNet GL-AR750S";

        chosen {
                bootargs = "console=ttyS0,115200n8";
        };

        aliases {
                led-boot = &power;
                led-failsafe = &power;
                led-running = &power;
                led-upgrade = &power;
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <20>;
                pinctrl-names = "default";
                pinctrl-0 = <&jtag_disable_pins>;

                reset {
                        label = "reset";
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
                };

                mode {
                        label = "mode";
                        linux,code = <BTN_0>;
                        linux,input-type = <EV_SW>;
                        gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
                };
        };

        leds {
                compatible = "gpio-leds";

                power: power {
                        label = "gl-ar750s:green:power";
                        gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
                        default-state = "keep";
                };

                wlan2g {
                        label = "gl-ar750s:green:wlan2g";
                        gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
                        linux,default-trigger = "phy1tpt";
                };

                wlan5g {
                        label = "gl-ar750s:green:wlan5g";
                        gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
                        linux,default-trigger = "phy0tpt";
                };
        };
};

&spi {
        status = "okay";
        num-cs = <0>;

        flash@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <25000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x040000>;
                                read-only;
                        };

                        partition@40000 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                        };

                        art: partition@50000 {
                                label = "art";
                                reg = <0x050000 0x010000>;
                        };

                        partition@60000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x060000 0xfa0000>;
                        };
                };
        };
};

&pcie {
        status = "okay";
};

&uart {
        status = "okay";
};

&usb0 {
        #address-cells = <1>;
        #size-cells = <0>;
        status = "okay";

        hub_port: port@1 {
                reg = <1>;
                #trigger-source-cells = <0>;
        };
};

&usb_phy0 {
        status = "okay";
};

&mdio0 {
        status = "okay";
        phy-mask = <0>;

        phy0: ethernet-phy@0 {
                reg = <0>;
                phy-mode = "sgmii";
                qca,ar8327-initvals = <
                        0x04 0x00080080 /* PORT0 PAD MODE CTRL */
                        0x7c 0x0000007e /* PORT0_STATUS */
                >;
        };
};

&eth0 {
        status = "okay";

        mtd-mac-address = <&art 0x0>;
        phy-handle = <&phy0>;
};

&wmac {
        status = "okay";
        mtd-cal-data = <&art 0x1000>;
        mtd-mac-address = <&art 0x1002>;
};