OpenWrt – Rev 1
?pathlinks?
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9344.dtsi"
/ {
aliases {
led-boot = &system;
led-failsafe = &system;
led-running = &system;
led-upgrade = &system;
};
leds {
compatible = "gpio-leds";
usb1 {
label = "tp-link:green:usb1";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
trigger-sources = <&hub_port1>;
linux,default-trigger = "usbport";
};
usb2 {
label = "tp-link:green:usb2";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
trigger-sources = <&hub_port2>;
linux,default-trigger = "usbport";
};
wlan2g {
label = "tp-link:green:wlan2g";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
system: system {
label = "tp-link:green:system";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
qss {
label = "tp-link:green:qss";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
};
ath9k-leds {
compatible = "gpio-leds";
wlan5g {
label = "tp-link:green:wlan5g";
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wifi {
linux,code = <KEY_RFKILL>;
linux,input-type = <EV_SW>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
gpio-export {
compatible = "gpio-export";
gpio_usb1_power {
gpio-export,name = "tp-link:power:usb1";
gpio-export,output = <1>;
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
};
gpio_usb2_power {
gpio-export,name = "tp-link:power:usb2";
gpio-export,output = <1>;
gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
};
gpio_ext_lna0 {
gpio-export,name = "tp-link:ext:lna0";
gpio-export,output = <1>;
gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
};
gpio_ext_lna1 {
gpio-export,name = "tp-link:ext:lna1";
gpio-export,output = <1>;
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
};
};
};
&ref {
clock-frequency = <40000000>;
};
&uart {
status = "okay";
};
&gpio {
status = "okay";
};
&spi {
num-cs = <1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
compatible = "tplink,firmware";
label = "firmware";
reg = <0x020000 0x7d0000>;
};
art: partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&usb {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
port@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
#trigger-source-cells = <0>;
hub_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
hub_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
};
&usb_phy {
status = "okay";
};
&pcie {
status = "okay";
ath9k: wifi@0,0 {
compatible = "pci168c,0033";
reg = <0x0000 0 0 0 0>;
mtd-mac-address = <&uboot 0x1fc00>;
qca,no-eeprom;
#gpio-cells = <2>;
gpio-controller;
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&uboot 0x1fc00>;
mtd-mac-address-increment = <(-1)>;
};
&mdio0 {
status = "okay";
phy-mask = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
qca,ar8327-initvals = <
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
0x10 0x80000080 /* POWER_ON_STRIP */
0x50 0xc737c737 /* LED_CTRL0 */
0x54 0x00000000 /* LED_CTRL1 */
0x58 0x00000000 /* LED_CTRL2 */
0x5c 0x0030c300 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};
ð0 {
status = "okay";
/* default for ar934x, except for 1000M */
pll-data = <0x06000000 0x00000101 0x00001616>;
mtd-mac-address = <&uboot 0x1fc00>;
mtd-mac-address-increment = <(-2)>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
};