OpenWrt – Rev 4

Subversion Repositories:
Rev:
/dts-v1/;

#include "rt3050.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
        compatible = "netgear,wnce2001", "ralink,rt3052-soc";
        model = "Netgear WNCE2001";

        chosen {
                bootargs = "console=ttyS0,115200";
        };

        gpio-leds {
                compatible = "gpio-leds";

                power-green {
                        label = "wnce2001:green:power";
                        gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
                };

                power-red {
                        label = "wnce2001:red:power";
                        gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
                };

                wlan-green {
                        label = "wnce2001:green:wlan";
                        gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
                };

                wlan-red {
                        label = "wnce2001:red:wlan";
                        gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
                };
        };

        gpio-keys-polled {
                compatible = "gpio-keys-polled";
                #address-cells = <1>;
                #size-cells = <0>;
                poll-interval = <20>;

                reset {
                        label = "reset";
                        gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
                        linux,code = <KEY_RESTART>;
                };

                wps {
                        label = "wps";
                        gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
                        linux,code = <KEY_WPS_BUTTON>;
                };

                rt {
                        label = "rt";
                        gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
                        linux,code = <BTN_0>;
                };

                ap {
                        label = "ap";
                        gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
                        linux,code = <BTN_1>;
                };
        };
};

&spi0 {
        status = "okay";

        m25p80@0 {
                #address-cells = <1>;
                #size-cells = <1>;
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <10000000>;

                partition@0 {
                        label = "u-boot";
                        reg = <0x0 0x30000>;
                        read-only;
                };

                factory: partition@30000 {
                        label = "factory";
                        reg = <0x30000 0x10000>;
                        read-only;
                };

                partition@40000 {
                        label = "config";
                        reg = <0x40000 0x20000>;
                        read-only;
                };

                partition@60000 {
                        label = "language";
                        reg = <0x60000 0x30000>;
                        read-only;
                };

                partition@90000 {
                        label = "pot";
                        reg = <0x90000 0x10000>;
                        read-only;
                };

                partition@a0000 {
                        label = "checksum";
                        reg = <0xa0000 0x10000>;
                };

                partition@b0000 {
                        label = "firmware";
                        reg = <0xb0000 0x350000>;
                };
        };
};

&pinctrl {
        state_default: pinctrl0 {
                gpio {
                        ralink,group = "i2c", "jtag", "rgmii", "mdio", "uartf";
                        ralink,function = "gpio";
                };
        };
};

&ethernet {
        mtd-mac-address = <&factory 0x28>;
};

&wmac {
        ralink,mtd-eeprom = <&factory 0>;
};