OpenWrt – Rev 3

?pathlinks?

Rev 2 – Blame – Compare with Previous – Last modification – View Log – Download

/* This file is released into the public domain */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "mt7620a.dtsi"

/ {
        compatible = "netgear,ex3700", "ralink,mt7620a-soc";
        model = "Netgear EX3700/EX3800";

        chosen {
                bootargs = "console=ttyS0,57600";
        };

        gpio-leds {
                compatible = "gpio-leds";

                power_g {
                        label = "ex3700:green:power";
                        gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
                        default-state = "on";
                };

                power_a {
                        label = "ex3700:amber:power";
                        gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
                        default-state = "off";
                };

                router_g {
                        label = "ex3700:green:router";
                        gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
                };

                router_r {
                        label = "ex3700:red:router";
                        gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
                };

                device_g {
                        label = "ex3700:green:device";
                        gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
                };

                device_r {
                        label = "ex3700:red:device";
                        gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
                };

                wps {
                        label = "ex3700:green:wps";
                        gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
                };
        };

        gpio-keys-polled {
                compatible = "gpio-keys-polled";
                #address-cells = <1>;
                #size-cells = <0>;
                poll-interval = <20>;

                reset {
                        label = "reset";
                        gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
                        linux,code = <KEY_RESTART>;
                };

                wps {
                        label = "wps";
                        gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
                        linux,code = <KEY_WPS_BUTTON>;
                };
        };
};

&gpio0 {
        status = "okay";
};

&gpio2 {
        status = "okay";
};

&spi0 {
        status = "okay";

        m25p80@0 {
                #address-cells = <1>;
                #size-cells = <1>;
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <10000000>;

                partition@0 {
                        label = "u-boot";
                        reg = <0x0 0x30000>;
                        read-only;
                };

                partition@30000 {
                        label = "config";
                        reg = <0x30000 0x10000>;
                        read-only;
                };

                factory: partition@40000 {
                        label = "factory";
                        reg = <0x40000 0x10000>;
                        read-only;
                };

                partition@50000 {
                        label = "firmware";
                        reg = <0x50000 0x790000>;
                };

                partition@7e0000 {
                        label = "board_data";
                        reg = <0x7e0000 0x10000>;
                        read-only;
                };

                partition@7f0000 {
                        label = "nvram";
                        reg = <0x7f0000 0x10000>;
                        read-only;
                };
        };
};

&pcie {
        status = "okay";

        pcie-bridge {
                mt76@0,0 {
                        reg = <0x0000 0 0 0 0 >;
                        device_type = "pci";
                        mediatek,mtd-eeprom = <&factory 0x8000>;
                        ieee80211-freq-limit = <5000000 6000000>;
                };
        };
};

&ethernet {
        mtd-mac-address = <&factory 0x28>;
};

&wmac {
        ralink,mtd-eeprom = <&factory 0x0>;
};

&pinctrl {
        state_default: pinctrl0 {
                default {
                        ralink,group = "i2c", "rgmii2", "spi refclk";
                        ralink,function = "gpio";
                };
        };
};