OpenWrt – Rev 3
?pathlinks?
/dts-v1/;
#include "vr9.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/mips/lantiq_rcu_gphy.h>
/ {
compatible = "buffalo,wbmr-300hpd", "lantiq,xway", "lantiq,vr9";
model = "Buffalo WBMR-300HPD";
chosen {
bootargs = "console=ttyLTQ0,115200";
};
aliases {
led-boot = &power_g;
led-failsafe = &diag_r;
led-running = &power_g;
led-dsl = &dsl;
led-internet = &router_g;
led-wifi = &wifi_g;
};
memory@0 {
reg = <0x0 0x4000000>;
};
gpio_poweroff {
compatible = "gpio-poweroff";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
power {
label = "power";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
};
reset {
label = "reset";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
auto {
label = "auto";
gpios = <&gpio 48 GPIO_ACTIVE_HIGH>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
};
router {
label = "router";
gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
linux,code = <BTN_1>;
linux,input-type = <EV_SW>;
};
};
gpio-leds {
compatible = "gpio-leds";
diag_r: diag_r {
label = "wbmr300:red:diag";
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
default_state = "off";
};
wifi_g: wifi_g {
label = "wbmr300:green:wifi";
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
};
dsl: dsl {
label = "dsl";
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
};
router_y: router_y {
label = "wbmr300:yellow:router";
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
};
wifi_y: wifi_y {
label = "wbmr300:yellow:wifi";
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
};
lan1: lan1 {
label = "wbmr300:green:lan1";
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
};
wan: wan {
label = "wbmr300:green:wan";
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
};
lan3: lan3 {
label = "wbmr300:green:lan3";
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
};
lan2: lan2 {
label = "wbmr300:green:lan2";
gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
};
internet_g: internet_g {
label = "wbmr300:green:internet";
gpios = <&gpio 34 GPIO_ACTIVE_HIGH>;
};
internet_y: internet_y {
label = "wbmr300:yellow:internet";
gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
};
router_g: router_g {
label = "wbmr300:green:router";
gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
};
power_g: power_g {
label = "wbmr300:green:power";
gpios = <&gpio 49 GPIO_ACTIVE_HIGH>;
};
};
usb_vbus: regulator-usb-vbus {
compatible = "regulator-fixed";
regulator-name = "USB_VBUS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio 33 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
ð0 {
lan: interface@0 {
compatible = "lantiq,xrx200-pdi";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
lantiq,switch;
ethernet@1 {
compatible = "lantiq,xrx200-pdi-port";
reg = <4>;
phy-mode = "mii";
phy-handle = <&phy13>;
};
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";
reg = <5>;
phy-mode = "mii";
phy-handle = <&phy14>;
};
ethernet@3 {
compatible = "lantiq,xrx200-pdi-port";
reg = <2>;
phy-mode = "mii";
phy-handle = <&phy11>;
};
ethernet@4 {
compatible = "lantiq,xrx200-pdi-port";
reg = <3>;
phy-mode = "mii";
phy-handle = <&phy12>;
};
};
mdio@0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "lantiq,xrx200-mdio";
reg = <0>;
phy11: ethernet-phy@11 {
reg = <0x11>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
phy12: ethernet-phy@12 {
reg = <0x12>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
phy13: ethernet-phy@13 {
reg = <0x13>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
phy14: ethernet-phy@14 {
reg = <0x14>;
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
};
};
};
&gphy0 {
lantiq,gphy-mode = <GPHY_MODE_FE>;
};
&gphy1 {
lantiq,gphy-mode = <GPHY_MODE_FE>;
};
&gpio {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
mdio {
lantiq,groups = "mdio";
lantiq,function = "mdio";
};
phy-rst {
lantiq,pins = "io42";
lantiq,pull = <0>;
lantiq,open-drain = <0>;
lantiq,output = <1>;
};
pcie-rst {
lantiq,pins = "io38";
lantiq,pull = <0>;
lantiq,output = <1>;
};
};
pins_spi_default: pins_spi_default {
spi_in {
lantiq,groups = "spi_di";
lantiq,function = "spi";
};
spi_out {
lantiq,groups = "spi_do", "spi_clk",
"spi_cs4";
lantiq,function = "spi";
lantiq,output = <1>;
};
};
};
&spi {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pins_spi_default>;
m25p80@4 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <4 0>;
spi-max-frequency = <20000000>;
partition@0 {
reg = <0x0 0x10000>;
label = "u-boot";
read-only;
};
partition@10000 {
reg = <0x10000 0x10000>;
label = "gphyfirmware";
read-only;
};
partition@20000 {
reg = <0x20000 0x80000>;
label = "dsl_fw";
};
partition@de0000 {
reg = <0xa0000 0xf40000>;
label = "firmware";
};
partition@fe0000 {
reg = <0xfe0000 0x10000>;
label = "sysconfig";
read-only;
};
partition@ff0000 {
reg = <0xff0000 0x2000>;
label = "ubootconfig";
};
partition@ff3000 {
reg = <0xff3000 0x2000>;
label = "board_config";
read-only;
};
};
};
&usb_phy0 {
status = "okay";
phy-supply = <&usb_vbus>;
};
&usb_phy1 {
status = "okay";
phy-supply = <&usb_vbus>;
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};