OpenWrt – Rev 3
?pathlinks?
#include "vr9.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/mips/lantiq_rcu_gphy.h>
/ {
compatible = "tplink,tdw89x0", "lantiq,xway", "lantiq,vr9";
chosen {
bootargs = "console=ttyLTQ0,115200";
};
aliases {
/* the power led can't be controlled, use the wps led instead */
led-boot = &wps;
led-failsafe = &wps;
led-dsl = &dsl;
led-internet = &internet;
led-wifi = &wifi;
led-usb = &led_usb0;
led-usb2 = &led_usb2;
};
memory@0 {
reg = <0x0 0x4000000>;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
reset {
label = "reset";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wifi {
label = "wifi";
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_RFKILL>;
linux,input-type = <EV_SW>;
};
wps {
label = "wps";
gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
gpio-leds {
compatible = "gpio-leds";
/*
power is not controllable via gpio
*/
dsl: dsl {
label = "tdw89x0:green:dsl";
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
};
internet: internet {
label = "tdw89x0:green:internet";
gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
};
led_usb0: usb0 {
label = "tdw89x0:green:usb";
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
};
led_usb2: usb2 {
label = "tdw89x0:green:usb2";
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
};
wps: wps {
label = "tdw89x0:green:wps";
gpios = <&gpio 37 GPIO_ACTIVE_HIGH>;
};
};
wifi-leds {
compatible = "gpio-leds";
wifi: wifi {
label = "tdw89x0:green:wifi";
gpios = <&ath9k 0 GPIO_ACTIVE_HIGH>;
};
};
usb_vbus: regulator-usb-vbus {
compatible = "regulator-fixed";
regulator-name = "USB_VBUS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio 33 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
ð0 {
lan: interface@0 {
compatible = "lantiq,xrx200-pdi";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
mtd-mac-address = <&ath9k_cal 0xf100>;
lantiq,switch;
ethernet@0 {
compatible = "lantiq,xrx200-pdi-port";
reg = <0>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
// gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
};
ethernet@5 {
compatible = "lantiq,xrx200-pdi-port";
reg = <5>;
phy-mode = "rgmii";
phy-handle = <&phy5>;
};
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";
reg = <2>;
phy-mode = "gmii";
phy-handle = <&phy11>;
};
ethernet@3 {
compatible = "lantiq,xrx200-pdi-port";
reg = <4>;
phy-mode = "gmii";
phy-handle = <&phy13>;
};
};
mdio@0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "lantiq,xrx200-mdio";
reg = <0>;
phy0: ethernet-phy@0 {
reg = <0x0>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy5: ethernet-phy@5 {
reg = <0x5>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy11: ethernet-phy@11 {
reg = <0x11>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy13: ethernet-phy@13 {
reg = <0x13>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
};
};
&gphy0 {
lantiq,gphy-mode = <GPHY_MODE_GE>;
};
&gphy1 {
lantiq,gphy-mode = <GPHY_MODE_GE>;
};
&gpio {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
mdio {
lantiq,groups = "mdio";
lantiq,function = "mdio";
};
gphy-leds {
lantiq,groups = "gphy0 led1", "gphy1 led1";
lantiq,function = "gphy";
lantiq,pull = <2>;
lantiq,open-drain = <0>;
lantiq,output = <1>;
};
phy-rst {
lantiq,pins = "io42";
lantiq,pull = <0>;
lantiq,open-drain = <0>;
lantiq,output = <1>;
};
pcie-rst {
lantiq,pins = "io38";
lantiq,pull = <0>;
lantiq,output = <1>;
};
};
pins_spi_default: pins_spi_default {
spi_in {
lantiq,groups = "spi_di";
lantiq,function = "spi";
};
spi_out {
lantiq,groups = "spi_do", "spi_clk",
"spi_cs4";
lantiq,function = "spi";
lantiq,output = <1>;
};
};
};
&pcie0 {
pcie@0 {
reg = <0 0 0 0 0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
ath9k: wifi@168c,002e {
compatible = "pci168c,002e";
reg = <0 0 0 0 0>;
#gpio-cells = <2>;
gpio-controller;
qca,no-eeprom;
qca,disable-5ghz;
mtd-mac-address = <&ath9k_cal 0xf100>;
mtd-mac-address-increment = <2>;
};
};
};
&spi {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pins_spi_default>;
m25p80@4 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <4 0>;
spi-max-frequency = <33250000>;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x20000>;
label = "u-boot";
read-only;
};
partition@20000 {
reg = <0x20000 0x7a0000>;
label = "firmware";
};
partition@7c0000 {
reg = <0x7c0000 0x10000>;
label = "config";
read-only;
};
ath9k_cal: partition@7d0000 {
reg = <0x7d0000 0x30000>;
label = "boardconfig";
read-only;
};
};
};
};
&usb_phy0 {
status = "okay";
phy-supply = <&usb_vbus>;
};
&usb_phy1 {
status = "okay";
phy-supply = <&usb_vbus>;
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};