OpenWrt – Rev 3
?pathlinks?
#include "qcom-ipq8064-v2.0.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "TP-Link Archer C2600";
compatible = "tplink,c2600", "qcom,ipq8064";
memory@0 {
reg = <0x42000000 0x1e000000>;
device_type = "memory";
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
rsvd@41200000 {
reg = <0x41200000 0x300000>;
no-map;
};
};
aliases {
serial0 = &gsbi4_serial;
mdio-gpio0 = &mdio0;
led-boot = &power;
led-failsafe = &general;
led-running = &power;
led-upgrade = &general;
};
chosen {
linux,stdout-path = "serial0:115200n8";
};
soc {
pinmux@800000 {
button_pins: button_pins {
mux {
pins = "gpio16", "gpio54", "gpio65";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
i2c4_pins: i2c4_pinmux {
mux {
pins = "gpio12", "gpio13";
function = "gsbi4";
drive-strength = <12>;
bias-disable;
};
};
led_pins: led_pins {
mux {
pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33",
"gpio53", "gpio66";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
spi_pins: spi_pins {
mux {
pins = "gpio18", "gpio19", "gpio21";
function = "gsbi5";
bias-pull-down;
};
data {
pins = "gpio18", "gpio19";
drive-strength = <10>;
};
cs {
pins = "gpio20";
function = "gpio";
drive-strength = <10>;
bias-pull-up;
};
clk {
pins = "gpio21";
drive-strength = <12>;
};
};
mdio0_pins: mdio0_pins {
mux {
pins = "gpio0", "gpio1";
function = "gpio";
drive-strength = <8>;
bias-disable;
};
};
rgmii2_pins: rgmii2_pins {
mux {
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
function = "rgmii2";
drive-strength = <8>;
bias-disable;
};
};
usb0_pwr_en_pin: usb0_pwr_en_pin {
mux {
pins = "gpio25";
function = "gpio";
drive-strength = <10>;
bias-pull-up;
output-high;
};
};
usb1_pwr_en_pin: usb1_pwr_en_pin {
mux {
pins = "gpio23";
function = "gpio";
drive-strength = <10>;
bias-pull-up;
output-high;
};
};
};
gsbi@16300000 {
qcom,mode = <GSBI_PROT_I2C_UART>;
status = "ok";
serial@16340000 {
status = "ok";
};
/*
* The i2c device on gsbi4 should not be enabled.
* On ipq806x designs gsbi4 i2c is meant for exclusive
* RPM usage. Turning this on in kernel manifests as
* i2c failure for the RPM.
*/
};
gsbi5: gsbi@1a200000 {
qcom,mode = <GSBI_PROT_SPI>;
status = "ok";
spi5: spi@1a280000 {
status = "ok";
pinctrl-0 = <&spi_pins>;
pinctrl-names = "default";
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
flash: m25p80@0 {
compatible = "jedec,spi-nor";
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <50000000>;
reg = <0>;
SBL1@0 {
label = "SBL1";
reg = <0x0 0x20000>;
read-only;
};
MIBIB@20000 {
label = "MIBIB";
reg = <0x20000 0x20000>;
read-only;
};
SBL2@40000 {
label = "SBL2";
reg = <0x40000 0x20000>;
read-only;
};
SBL3@60000 {
label = "SBL3";
reg = <0x60000 0x30000>;
read-only;
};
DDRCONFIG@90000 {
label = "DDRCONFIG";
reg = <0x90000 0x10000>;
read-only;
};
SSD@a0000 {
label = "SSD";
reg = <0xa0000 0x10000>;
read-only;
};
TZ@b0000 {
label = "TZ";
reg = <0xb0000 0x30000>;
read-only;
};
RPM@e0000 {
label = "RPM";
reg = <0xe0000 0x20000>;
read-only;
};
fs-uboot@100000 {
label = "fs-uboot";
reg = <0x100000 0x70000>;
read-only;
};
uboot-env@170000 {
label = "uboot-env";
reg = <0x170000 0x40000>;
read-only;
};
radio@1b0000 {
label = "radio";
reg = <0x1b0000 0x40000>;
read-only;
};
os-image@1f0000 {
label = "os-image";
reg = <0x1f0000 0x400000>;
};
rootfs@5f0000 {
label = "rootfs";
reg = <0x5f0000 0x1900000>;
};
defaultmac: default-mac@1ef0000 {
label = "default-mac";
reg = <0x1ef0000 0x00200>;
read-only;
};
pin@1ef0200 {
label = "pin";
reg = <0x1ef0200 0x00200>;
read-only;
};
product-info@1ef0400 {
label = "product-info";
reg = <0x1ef0400 0x0fc00>;
read-only;
};
partition-table@1f00000 {
label = "partition-table";
reg = <0x1f00000 0x10000>;
read-only;
};
soft-version@1f10000 {
label = "soft-version";
reg = <0x1f10000 0x10000>;
read-only;
};
support-list@1f20000 {
label = "support-list";
reg = <0x1f20000 0x10000>;
read-only;
};
profile@1f30000 {
label = "profile";
reg = <0x1f30000 0x10000>;
read-only;
};
default-config@1f40000 {
label = "default-config";
reg = <0x1f40000 0x10000>;
read-only;
};
user-config@1f50000 {
label = "user-config";
reg = <0x1f50000 0x40000>;
read-only;
};
qos-db@1f90000 {
label = "qos-db";
reg = <0x1f90000 0x40000>;
read-only;
};
usb-config@1fd0000 {
label = "usb-config";
reg = <0x1fd0000 0x10000>;
read-only;
};
log@1fe0000 {
label = "log";
reg = <0x1fe0000 0x20000>;
read-only;
};
};
};
};
phy@100f8800 { /* USB3 port 1 HS phy */
status = "ok";
};
phy@100f8830 { /* USB3 port 1 SS phy */
status = "ok";
};
phy@110f8800 { /* USB3 port 0 HS phy */
status = "ok";
};
phy@110f8830 { /* USB3 port 0 SS phy */
status = "ok";
};
usb30@0 {
status = "ok";
pinctrl-0 = <&usb0_pwr_en_pin>;
pinctrl-names = "default";
};
usb30@1 {
status = "ok";
pinctrl-0 = <&usb1_pwr_en_pin>;
pinctrl-names = "default";
};
pcie0: pci@1b500000 {
status = "ok";
};
pcie1: pci@1b700000 {
status = "ok";
force_gen1 = <1>;
};
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&mdio0_pins>;
pinctrl-names = "default";
phy0: ethernet-phy@0 {
device_type = "ethernet-phy";
reg = <0>;
qca,ar8327-initvals = <
0x00004 0x7600000 /* PAD0_MODE */
0x00008 0x1000000 /* PAD5_MODE */
0x0000c 0x80 /* PAD6_MODE */
0x000e4 0x6a545 /* MAC_POWER_SEL */
0x000e0 0xc74164de /* SGMII_CTRL */
0x0007c 0x4e /* PORT0_STATUS */
0x00094 0x4e /* PORT6_STATUS */
>;
};
phy4: ethernet-phy@4 {
device_type = "ethernet-phy";
reg = <4>;
};
};
gmac1: ethernet@37200000 {
status = "ok";
phy-mode = "rgmii";
qcom,id = <1>;
pinctrl-0 = <&rgmii2_pins>;
pinctrl-names = "default";
mtd-mac-address = <&defaultmac 0x8>;
mtd-mac-address-increment = <1>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
gmac2: ethernet@37400000 {
status = "ok";
phy-mode = "sgmii";
qcom,id = <2>;
mtd-mac-address = <&defaultmac 0x8>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&button_pins>;
pinctrl-names = "default";
wifi {
label = "wifi";
gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
reset {
label = "reset";
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
ledswitch {
label = "ledswitch";
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_LIGHTS_TOGGLE>;
};
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-0 = <&led_pins>;
pinctrl-names = "default";
lan {
label = "c2600:white:lan";
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
};
usb4 {
label = "c2600:white:usb_4";
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
};
usb2 {
label = "c2600:white:usb_2";
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
};
wps {
label = "c2600:white:wps";
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
};
wan_amber {
label = "c2600:amber:wan";
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
};
wan_white {
label = "c2600:white:wan";
gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>;
};
power: power {
label = "c2600:white:power";
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
default-state = "keep";
};
general: general {
label = "c2600:white:general";
gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
};
};
};
&adm_dma {
status = "ok";
};