OpenWrt – Rev 3
?pathlinks?
#!/bin/sh /etc/rc.common
# Copyright (C) 2012 OpenWrt.org
START=97
USE_PROCD=1
EXTRA_COMMANDS="status lucistat"
EXTRA_HELP=" status Get DSL status information
lucistat Get status information if lua friendly format"
[ -f /lib/functions/lantiq_dsl.sh ] && . /lib/functions/lantiq_dsl.sh
#
# ITU-T G.997.1 (06/2012) - Section 7.3.1.1.1 (xTU transmission system enabling (XTSE))
# ITU-T G.997.1 Amendment 2 (04/2013) - Section 2.1 - (Vectoring mode enable (VECTORMODE_ENABLE))
#
# G.992.1 Annex A
# G.992.2 Annex A
# G.992.3 Annex A / L-US1 / L_US-2 / M
# G.992.5 Annex A / M
# G.993.2 Annex A/B/C
# G.993.5 Annex A/B/C
xtse_xdsl_a="05_01_04_00_4C_01_04_07"
# G.992.1 Annex B
# G.992.3 Annex B
# G.992.5 Annex B
# G.993.2 Annex A/B/C
# G.993.5 Annex A/B/C
xtse_xdsl_b="10_00_10_00_00_04_00_07"
# G.992.1 Annex B
# G.992.3 Annex B
# G.992.3 Annex J
# G.992.5 Annex B
# G.992.5 Annex J
# G.993.2 Annex A/B/C
# G.993.5 Annex A/B/C
xtse_xdsl_j="10_00_10_40_00_04_01_07"
# G.992.1 Annex B
xtse_xdsl_bdmt="10_00_00_00_00_00_00_00"
# G.992.3 Annex B
xtse_xdsl_b2="00_00_10_00_00_00_00_00"
# G.992.5 Annex B
xtse_xdsl_b2p="00_00_00_00_00_04_00_00"
# ANSI T1.413
xtse_xdsl_at1="01_00_00_00_00_00_00_00"
# G.992.2 Annex A
xtse_xdsl_alite="00_01_00_00_00_00_00_00"
# G.992.1 Annex A
xtse_xdsl_admt="04_00_00_00_00_00_00_00"
# G.992.3 Annex A
xtse_xdsl_a2="00_00_04_00_00_00_00_00"
# G.992.5 Annex A
xtse_xdsl_a2p="00_00_00_00_00_01_00_00"
# G.992.3 Annex L
xtse_xdsl_l="00_00_00_00_0C_00_00_00"
# G.992.3 Annex M
# G.992.5 Annex M
xtse_xdsl_m="00_00_00_00_40_00_04_00"
# G.992.3 Annex M
xtse_xdsl_m2="00_00_00_00_40_00_00_00"
# G.992.5 Annex M
xtse_xdsl_m2p="00_00_00_00_00_00_04_00"
#
# ITU-T G.994.1 (06/2012) - Table 2 (Mandatory carrier sets)
#
# A43
tone_adsl_a="0x142" # A43C + J43 + A43
tone_vdsl_a="0x142" # A43C + J43 + A43
# A43 + V43
tone_adsl_av="0x142" # A43C + J43 + A43
tone_vdsl_av="0x146" # A43C + J43 + A43 + V43
# B43
tone_adsl_b="0x81" # B43 + B43c
tone_vdsl_b="0x1" # B43
# B43 + V43
tone_adsl_bv="0x81" # B43 + B43c
tone_vdsl_bv="0x5" # B43 + V43
# create ADSL autoboot script. Used for SNR margin tweak
autoboot_script() {
echo "[WaitForConfiguration]={
locs 0 $1
}
[WaitForLinkActivate]={
}
[WaitForRestart]={
}
[Common]={
}" > /tmp/dsl.scr
}
lowlevel_cfg() {
echo "# VRX Low Level Configuration File
#
# Parameters must be separated by tabs or spaces.
# Empty lines and comments will be ignored.
#
# nFilter
#
# NA = -1
# OFF = 0
# ISDN = 1
# POTS = 2
# POTS_2 = 3
# POTS_3 = 4
#
# (dec)
-1
# nHsToneGroupMode nHsToneGroup_A nHsToneGroup_V nHsToneGroup_AV
#
# NA = -1 NA = -1 see see
# AUTO = 0 VDSL2_B43 = 0x0001 nHsToneGroup_A nHsToneGroup_A
# MANUAL = 1 VDSL2_A43 = 0x0002
# VDSL2_V43 = 0x0004
# VDSL1_V43P = 0x0008
# VDSL1_V43I = 0x0010
# ADSL1_C43 = 0x0020
# ADSL2_J43 = 0x0040
# ADSL2_B43C = 0x0080
# ADSL2_A43C = 0x0100
#
# (dec) (hex) (hex) (hex)
1 $1 $2 0x0
# nBaseAddr nIrqNum
#
# (hex) (dec)
0x1e116000 63
# nUtopiaPhyAdr nUtopiaBusWidth nPosPhyParity
# default(16b) = 0 NA = -1
# 8-bit = 1 ODD = 0
# 16-bit = 2
#
#
# (hex) (dec) (dec)
0xFF 0 0
# bNtrEnable
#
# (dec)
0" > /tmp/lowlevel.cfg
}
service_triggers() {
procd_add_reload_trigger network
}
start_service() {
local annex
local firmware
local tone
local tone_adsl
local tone_vdsl
local xtse
local xfer_mode
local line_mode
local tc_layer
local mode
local lowlevel
local snr
config_load network
config_get tone dsl tone
config_get annex dsl annex
config_get firmware dsl firmware
config_get xfer_mode dsl xfer_mode
config_get line_mode dsl line_mode
config_get snr dsl ds_snr_offset
eval "xtse=\"\${xtse_xdsl_$annex}\""
case "${xfer_mode}" in
atm)
tc_layer="-T1:0x1:0x1_1:0x1:0x1"
;;
ptm)
tc_layer="-T2:0x1:0x1_2:0x1:0x1"
;;
esac
case "${line_mode}" in
adsl)
mode="-M1"
# mask out VDSL bits when ADSL is requested
xtse="${xtse%_*}_00"
;;
vdsl)
mode="-M2"
# mask out ADSL bits when VDSL is requested
xtse="00_00_00_00_00_00_00_${xtse##*_}"
;;
esac
local annexgpio="/sys/class/gpio/annex"
if [ -d "${annexgpio}a" ] && [ -d "${annexgpio}b" ]; then
case "${annex}" in
a*|l*|m*)
echo 1 > "${annexgpio}a/value"
echo 0 > "${annexgpio}b/value"
;;
b*|j*)
echo 0 > "${annexgpio}a/value"
echo 1 > "${annexgpio}b/value"
;;
esac
fi
if [ -z "${firmware}" ]; then
# search for the firmware provided by dsl-vrx200-firmware-xdsl-*
if grep -qE "system type.*: (VR9|xRX200)" /proc/cpuinfo; then
case "${annex}" in
a*|l*|m*)
if [ -f "/lib/firmware/lantiq-vrx200-a.bin" ]; then
firmware="/lib/firmware/lantiq-vrx200-a.bin"
elif [ -f "/tmp/lantiq-vrx200-a.bin" ]; then
firmware="/tmp/lantiq-vrx200-a.bin"
elif [ -f "/lib/firmware/lantiq-vrx200-b.bin" ] && [ -f "/lib/firmware/lantiq-vrx200-b-to-a.bspatch" ]; then
bspatch /lib/firmware/lantiq-vrx200-b.bin \
/tmp/lantiq-vrx200-a.bin \
/lib/firmware/lantiq-vrx200-b-to-a.bspatch
firmware="/tmp/lantiq-vrx200-a.bin"
else
echo "firmware for annex a not found"
return 1
fi
;;
b*|j*)
if [ -f "/lib/firmware/lantiq-vrx200-b.bin" ]; then
firmware="/lib/firmware/lantiq-vrx200-b.bin"
elif [ -f "/tmp/lantiq-vrx200-b.bin" ]; then
firmware="/tmp/lantiq-vrx200-b.bin"
elif [ -f "/lib/firmware/lantiq-vrx200-a.bin" ] && [ -f "/lib/firmware/lantiq-vrx200-a-to-b.bspatch" ]; then
bspatch /lib/firmware/lantiq-vrx200-a.bin \
/tmp/lantiq-vrx200-b.bin \
/lib/firmware/lantiq-vrx200-a-to-b.bspatch
firmware="/tmp/lantiq-vrx200-b.bin"
else
echo "firmware for annex b not found"
return 1
fi
;;
*)
echo "annex type not supported use a or b"
return 1
;;
esac
fi
fi
[ -z "${firmware}" ] && firmware=/lib/firmware/vdsl.bin
[ -f "${firmware}" ] || {
echo failed to find $firmware
return 1
}
eval "tone_adsl=\"\${tone_adsl_$tone}\""
eval "tone_vdsl=\"\${tone_vdsl_$tone}\""
[ -n "${tone_adsl}" ] && [ -n "${tone_vdsl}" ] && {
lowlevel_cfg "${tone_adsl}" "${tone_vdsl}"
lowlevel="-l /tmp/lowlevel.cfg"
}
[ -z "${snr}" ] || {
# for SNR offset setting
autoboot_script "$snr"
autoboot="-a /tmp/dsl.scr -A /tmp/dsl.scr"
}
procd_open_instance
procd_set_param command /sbin/vdsl_cpe_control \
-i$xtse \
-n /sbin/dsl_notify.sh \
-f ${firmware} \
$lowlevel \
${mode} \
${tc_layer} \
$autoboot
procd_close_instance
}
stop_service() {
# do not use dsl_cmd to not block when this is locked up by some other proess
echo quit > /tmp/pipe/dsl_cpe0_cmd
DSL_NOTIFICATION_TYPE="DSL_INTERFACE_STATUS" \
DSL_INTERFACE_STATUS="DOWN" \
/sbin/dsl_notify.sh
}