OpenWrt – Rev 1

?pathlinks?

Blame – Last modification – View Log – Download

/dts-v1/;

#include "vr9.dtsi"

#include <dt-bindings/input/input.h>
#include <dt-bindings/mips/lantiq_rcu_gphy.h>

/ {
        compatible = "alphanetworks,asl56026", "lantiq,xway", "lantiq,vr9";
        model = "BT OpenReach VDSL Modem";

        chosen {
                bootargs = "console=ttyLTQ0,115200";
        };

        aliases {
                led-boot = &power_green;
                led-failsafe = &power_red;
                led-running = &power_green;
                led-upgrade = &power_green;

                led-dsl = &dsl;
        };

        memory@0 {
                reg = <0x0 0x2000000>;
        };

        gpio-keys-polled {
                compatible = "gpio-keys-polled";
                #address-cells = <1>;
                #size-cells = <0>;
                poll-interval = <100>;

                reset {
                        label = "reset";
                        gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
                        linux,code = <KEY_RESTART>;
                };
        };

        gpio-leds {
                compatible = "gpio-leds";

                dsl: dsl {
                        label = "asl56026:green:dsl";
                        gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
                };

                /* power-* is a bicolour led */
                power_green: power_green {
                        label = "asl56026:green:power";
                        gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
                        default-state = "keep";
                };

                power_red: power_red {
                        label = "asl56026:red:power";
                        gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
                };
        };

        gpio_export {
                compatible = "gpio-export";
                #size-cells = <0>;

                power_led_blink {
                        gpio-export,name = "power_led_blink";
                        gpio-export,output = <0>;
                        gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
                };
        };
};

&eth0 {
        lan: interface@0 {
                compatible = "lantiq,xrx200-pdi";
                #address-cells = <1>;
                #size-cells = <0>;
                reg = <0>;
                lantiq,switch;

                ethernet@2 {
                        compatible = "lantiq,xrx200-pdi-port";
                        reg = <2>;
                        phy-mode = "mii";
                        phy-handle = <&phy11>;
                };

                ethernet@3 {
                        compatible = "lantiq,xrx200-pdi-port";
                        reg = <3>;
                        phy-mode = "mii";
                        phy-handle = <&phy14>;
                };
        };

        mdio@0 {
                #address-cells = <1>;
                #size-cells = <0>;
                compatible = "lantiq,xrx200-mdio";
                reg = <0>;

                phy11: ethernet-phy@11 {
                        reg = <0x11>;
                        compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
                };

                phy14: ethernet-phy@14 {
                        reg = <0x14>;
                        compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
                };
        };
};

&gphy0 {
        lantiq,gphy-mode = <GPHY_MODE_FE>;
};

&gphy1 {
        lantiq,gphy-mode = <GPHY_MODE_FE>;
};

&gpio {
        pinctrl-names = "default";
        pinctrl-0 = <&state_default>;

        state_default: pinmux {
                mdio {
                        lantiq,groups = "mdio";
                        lantiq,function = "mdio";
                };
        };
};

&localbus {
        nor@0 {
                compatible = "lantiq,nor";
                bank-width = <2>;
                reg = <0 0x0 0x0800000>;
                #address-cells = <1>;
                #size-cells = <1>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "uboot";
                                reg = <0x0 0x30000>;
                        };

                        partition@30000 {
                                label = "uboot_env";
                                reg = <0x30000 0x10000>;
                        };

                        partition@40000 {
                                label = "firmware";
                                reg = <0x40000 0x750000>;
                        };

                        partition@790000 {
                                label = "ddrconfig";
                                reg = <0x790000 0x70000>;
                                read-only;
                        };
                };
        };
};