OpenWrt – Rev 4

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca956x.dtsi"

/ {
        model = "ROSINSON WR818";
        compatible = "rosinson,wr818", "qca,qca9560";

        chosen {
                bootargs = "console=ttyS0,115200n8";
        };

        aliases {
                led-boot = &system;
                led-failsafe = &system;
                led-running = &system;
                led-upgrade = &system;
        };

        gpio_leds: leds {
                compatible = "gpio-leds";

                system: system {
                        label = "wr818:red:system";
                        gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
                };

                wifi_2g {
                        label = "wr818:red:wifi2g";
                        gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
                        linux,default-trigger = "phy0tpt";
                };
        };

        keys {
                compatible = "gpio-keys";

                reset {
                        label = "reset";
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
                        debounce-interval = <60>;
                };
        };
};

&uart {
        status = "okay";
};

&gpio {
        status = "okay";
};

&spi {
        num-cs = <1>;

        status = "okay";

        flash@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <25000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x040000>;
                                read-only;
                        };

                        partition@40000 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                                read-only;
                        };

                        info: partition@50000 {
                                label = "factory";
                                reg = <0x050000 0x010000>;
                                read-only;
                        };

                        partition@60000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x060000 0xf80000>;
                        };

                        art: partition@ff0000 {
                                label = "art";
                                reg = <0xff0000 0x010000>;
                                read-only;
                        };
                };
        };
};

&mdio0 {
        status = "okay";

        phy-mask = <0>;
        phy0: ethernet-phy@0 {
                reg = <0>;
                phy-mode = "sgmii";

                qca,ar8327-initvals = <
                        0x04 0x00080080 /* PORT0 PAD MODE CTRL */
                        0x7c 0x0000007e /* PORT0_STATUS */
                >;
        };
};

&eth0 {
        status = "okay";

        mtd-mac-address = <&info 0x0>;
        phy-mode = "sgmii";
        phy-handle = <&phy0>;
};

&wmac {
        status = "okay";
        mtd-cal-data = <&art 0x1000>;
};

&usb_phy0 {
        status = "okay";
};

&usb0 {
        #address-cells = <1>;
        #size-cells = <0>;
        status = "okay";

        port@1 {
                reg = <1>;
                #trigger-source-cells = <0>;
        };
};

&usb_phy1 {
        status = "okay";
};

&usb1 {
        #address-cells = <1>;
        #size-cells = <0>;
        status = "okay";

        port@2 {
                reg = <2>;
                #trigger-source-cells = <0>;
        };
};