OpenWrt – Rev 1

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca9557.dtsi"

/ {
        compatible = "openmesh,om5p-ac-v2", "qca,qca9557";
        model = "OpenMesh OM5P-AC V2";

        extosc: ref {
                compatible = "fixed-clock";
                #clock-cells = <0>;
                clock-output-names = "ref";
                clock-frequency = <40000000>;
        };

        leds {
                compatible = "gpio-leds";

                power {
                        label = "om5pac:blue:power";
                        gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
                };

                wifi_green {
                        label = "om5pac:green:wifi";
                        gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
                };

                wifi_yellow {
                        label = "om5pac:yellow:wifi";
                        gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
                };

                wifi_red {
                        label = "om5pac:red:wifi";
                        gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
                };
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <100>;

                button0 {
                        label = "reset";
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
                };
        };

        gpio-export {
                compatible = "gpio-export";
                #size-cells = <0>;

                gpio_pa_dcdc {
                        gpio-export,name = "om5pac:pa_dcdc";
                        gpio-export,output = <1>;
                        gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
                };
                gpio_pa_high {
                        gpio-export,name = "om5pac:pa_high";
                        gpio-export,output = <1>;
                        gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
                };
        };
};

&pinmux {
        pinmux_pa_dcdc_pins {
                pinctrl-single,bits = <0x0 0xff00 0x0>;
        };

        pinmux_pa_high_pins {
                pinctrl-single,bits = <0x10 0xff 0x0>;
        };
};

&pcie0 {
        status = "okay";
};

&uart {
        status = "okay";
};

&pll {
        clocks = <&extosc>;
};

&spi {
        status = "okay";
        num-cs = <1>;

        flash@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <25000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x040000>;
                                read-only;
                        };

                        partition@1 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                        };

                        partition@2 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x850000 0x7a0000>;
                        };

                        partition@3 {
                                label = "ART";
                                reg = <0xff0000 0x010000>;
                                read-only;
                        };
                };
        };
};

&mdio0 {
        status = "okay";

        phy4: ethernet-phy@4 {
                reg = <4>;
                phy-mode = "rgmii-id";
        };
};

&mdio1 {
        status = "okay";

        phy1: ethernet-phy@1 {
                reg = <1>;
                phy-mode = "sgmii";
        };
};

&eth0 {
        status = "okay";

        pll-data = <0x82000101 0x80000101 0x80001313>;

        phy-handle = <&phy4>;
        phy-mode = "rgmii";
};

&eth1 {
        status = "okay";

        pll-data = <0x03000101 0x80000101 0x80001313>;

        phy-handle = <&phy1>;
        phy-mode = "sgmii";
};