OpenWrt – Rev 1

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

/*
 * The hardware of this board family is most likely shared with other devices
 * from other manufacturers.
 * Devolo seems to use hardware from Edimax, namely the Edimax WAP1750.
 *
 * The base board is identical but the single models differ in number of
 * buttons, ethernet ports, external console, USB, external / internal
 * antennas and number of spatial streams.
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca9557.dtsi"

/ {
        chosen {
                bootargs = "console=ttyS0,115200n8";
        };

        keys {
                compatible = "gpio-keys";

                reset {
                        label = "Reset button";
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
                        debounce-interval = <60>;
                };
        };

        watchdog {
                compatible = "linux,wdt-gpio";
                gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
                hw_algo = "toggle";
                hw_margin_ms = <300>;
                always-running;
        };
};

&pcie0 {
        status = "okay";
};

&uart {
        status = "okay";
};

&gpio {
        status = "okay";
};

&spi {
        status = "okay";
        num-cs = <1>;

        flash@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <25000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x040000>;
                                read-only;
                        };

                        partition@40000 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                                read-only;
                        };

                        art: partition@50000 {
                                label = "art";
                                reg = <0x050000 0x010000>;
                                read-only;
                        };

                        partition@60000 {
                                label = "art_bak";
                                reg = <0x060000 0x010000>;
                                read-only;
                        };

                        partition@70000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x070000 0xf90000>;
                        };
                };
        };
};

&mdio0 {
        status = "okay";

        phy4: ethernet-phy@4 {
                reg = <4>;
                at803x-disable-smarteee;
        };
};

&eth0 {
        status = "okay";

        mtd-mac-address = <&art 0x00>;
        phy-handle = <&phy4>;
        pll-data = <0xae000000 0x80000101 0x80001313>;

        gmac_config: gmac-config {
                device = <&gmac>;

                rxdv-delay = <3>;
                rxd-delay = <3>;
                txen-delay = <0>;
                txd-delay = <0>;
                rgmii-enabled = <1>;
        };
};

&mdio1 {
        phy1: ethernet-phy@1 {
                reg = <1>;
        };
};

&eth1 {
        mtd-mac-address = <&art 0x00>;
        mtd-mac-address-increment = <1>;
        phy-handle = <&phy1>;
        pll-data = <0x03000101 0x00000101 0x00001313>;
};

&wmac {
        status = "okay";
        mtd-cal-data = <&art 0x1000>;
        mtd-mac-address = <&art 0x00>;
        mtd-mac-address-increment = <(-2)>;
};