OpenWrt – Rev 1

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca953x.dtsi"

/ {
        compatible = "comfast,cf-e110n-v2", "qca,qca9533";
        model = "COMFAST CF-E110N v2";

        aliases {
                serial0 = &uart;
                led-boot = &wan;
                led-failsafe = &wan;
                led-upgrade = &wan;
        };

        leds {
                compatible = "gpio-leds";

                pinctrl-names = "default";
                pinctrl-0 = <&jtag_disable_pins &led_rssilow_pin &led_rssimediumhigh_pin &led_rssihigh_pin>;

                wan: wan {
                        label = "cf-e110n-v2:green:wan";
                        gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
                };

                lan {
                        label = "cf-e110n-v2:green:lan";
                        gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
                };

                rssilow {
                        label = "cf-e110n-v2:red:rssilow";
                        gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
                };

                rssimediumlow {
                        label = "cf-e110n-v2:red:rssimediumlow";
                        gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
                };

                rssimediumhigh {
                        label = "cf-e110n-v2:green:rssimediumhigh";
                        gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
                };

                rssihigh {
                        label = "cf-e110n-v2:green:rssihigh";
                        gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
                };
        };

        ath9k-leds {
                compatible = "gpio-leds";

                wlan {
                        label = "cf-e110n-v2:green:wlan";
                        gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
                        linux,default-trigger = "phy0tpt";
                };
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <20>;

                reset {
                        label = "reset";
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
                        debounce-interval = <60>;
                };
        };
};

&pinmux {
        led_rssilow_pin: pinmux_rssilow_pin {
                pinctrl-single,bits = <0x8 0x0 0xff000000>;
        };

        led_rssimediumhigh_pin: pinmux_rssimediumhigh_pin {
                pinctrl-single,bits = <0xc 0x0 0x00ff0000>;
        };

        led_rssihigh_pin: pinmux_rssihigh_pin {
                pinctrl-single,bits = <0x10 0x0 0x000000ff>;
        };
};

&spi {
        status = "okay";
        num-cs = <1>;

        flash@0 {
                compatible = "winbond,w25q128", "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <25000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x010000>;
                                read-only;
                        };

                        art: partition@10000 {
                                label = "art";
                                reg = <0x010000 0x010000>;
                                read-only;
                        };

                        partition@20000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x020000 0xfd0000>;
                        };

                        partition@ff0000 {
                                label = "nvram";
                                reg = <0xff0000 0x010000>;
                                read-only;
                        };
                };
        };
};

&uart {
        status = "okay";
};

&eth0 {
        status = "okay";
        mtd-mac-address = <&art 0x0>;
        phy-handle = <&swphy4>;
};

&eth1 {
        status = "okay";
        mtd-mac-address = <&art 0x1002>;

        gmac-config {
                device = <&gmac>;
        };
};

&wmac {
        status = "okay";
        mtd-cal-data = <&art 0x1000>;
        mtd-mac-address = <&art 0x6>;
};