OpenWrt – Rev 1

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "ar9344.dtsi"

/ {
        model = "OCEDO Raccoon";
        compatible = "ocedo,raccoon", "qca,ar9344";

        chosen {
                bootargs = "console=ttyS0,115200n8";
        };

        aliases {
                led-boot = &system;
                led-failsafe = &system;
                led-running = &system;
                led-upgrade = &system;
        };

        leds {
                compatible = "gpio-leds";

                power {
                        label = "raccoon:green:power";
                        gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
                        default-state = "on";
                };

                wlan2g {
                        label = "raccoon:yellow:wlan24";
                        gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
                        linux,default-trigger = "phy0tpt";
                };

                system: system {
                        label = "raccoon:blue:sys";
                        gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
                };
        };

        ath9k-leds {
                compatible = "gpio-leds";

                wlan5g {
                        label = "raccoon:red:wlan5";
                        gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
                        linux,default-trigger = "phy1tpt";
                };
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <20>;

                reset {
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
                        debounce-interval = <60>;
                };
        };
};

&ref {
        clock-frequency = <40000000>;
};

&uart {
        status = "okay";
};

&gpio {
        status = "okay";
};

&spi {
        num-cs = <1>;

        status = "okay";

        flash@0 {
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <25000000>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        uboot: partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x040000>;
                                read-only;
                        };

                        partition@40000 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                        };

                        partition@50000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x050000 0x740000>;
                        };

                        partition@790000 {
                                label = "vendor";
                                reg = <0x790000 0x740000>;
                                read-only;
                        };

                        partition@ed0000 {
                                label = "data";
                                reg = <0xed0000 0x110000>;
                                read-only;
                        };

                        partition@fe0000 {
                                label = "id";
                                reg = <0xfe0000 0x010000>;
                                read-only;
                        };

                        art: partition@ff0000 {
                                label = "art";
                                reg = <0xff0000 0x010000>;
                                read-only;
                        };
                };
        };
};

&pcie {
        status = "okay";

        ath9k: wifi@0,0 {
                compatible = "pci168c,0030";
                reg = <0x0000 0 0 0 0>;
                mtd-mac-address = <&art 0xc>;
                qca,no-eeprom;
                #gpio-cells = <2>;
                gpio-controller;
        };
};

&wmac {
        status = "okay";

        mtd-cal-data = <&art 0x1000>;
        mtd-mac-address = <&art 0x6>;
};

&mdio0 {
        status = "okay";

        phy-mask = <0>;

        phy0: ethernet-phy@0 {
                reg = <0>;
                phy-mode = "rgmii";
        };
};

&eth0 {
        status = "okay";

        /* default for ar934x, except for 1000M */
        pll-data = <0x06000000 0x00000101 0x00001616>;

        mtd-mac-address = <&art 0x0>;

        phy-mode = "rgmii";
        phy-handle = <&phy0>;
};