OpenWrt – Rev 4

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "ar9330.dtsi"

/ {
        model = "PQI Air-Pen";
        compatible = "pqi,air-pen", "qca,ar9330";

        aliases {
                serial0 = &uart;
                led-boot = &wlan;
                led-failsafe = &wlan;
                led-upgrade = &wlan;
        };

        leds {
                compatible = "gpio-leds";

                wlan: wlan {
                        label = "air-pen:blue:wlan";
                        gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
                        linux,default-trigger = "phy0tpt";
                };

                wps {
                        label = "air-pen:blue:wps";
                        gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
                };
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <100>;

                wps {
                        label = "wps";
                        linux,code = <KEY_WPS_BUTTON>;
                        gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
                        debounce-interval = <60>;
                };

                reset {
                        label = "reset";
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
                        debounce-interval = <60>;
                };
        };
};

&uart {
        status = "okay";
};

&gpio {
        status = "okay";
};

&usb {
        dr_mode = "host";
        status = "okay";
};

&usb_phy {
        status = "okay";
};

&spi {
        num-cs = <1>;
        status = "okay";

        flash@0 {
                compatible = "jedec,spi-nor";
                spi-max-frequency = <104000000>;
                reg = <0>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x040000>;
                                read-only;
                        };

                        partition@40000 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                        };

                        art: partition@50000 {
                                label = "art";
                                reg = <0x050000 0x010000>;
                                read-only;
                        };

                        partition@60000 {
                                label = "NVRAM";
                                reg = <0x060000 0x010000>;
                                read-only;
                        };

                        partition@70000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x070000 0x780000>;
                        };

                        partition@7f0000 {
                                label = "CONF";
                                reg = <0x7f0000 0x010000>;
                                read-only;
                        };
                };
        };
};

&eth0 {
        status = "okay";

        mtd-mac-address = <&art 0x1002>;

        gmac-config {
                device = <&gmac>;

                switch-phy-addr-swap = <0>;
                switch-phy-swap = <0>;
        };
};

&eth1 {
        status = "okay";
        compatible = "syscon", "simple-mfd";
};

&wmac {
        status = "okay";
        mtd-cal-data = <&art 0x1000>;
        mtd-mac-address = <&art 0x2>;
};