OpenWrt – Rev 4

Subversion Repositories:
Rev:
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "ar9330.dtsi"

/ {
        model = "GL.iNet GL-AR150";
        compatible = "glinet,gl-ar150", "qca,ar9330";

        aliases {
                serial0 = &uart;
                led-boot = &wlan;
                led-failsafe = &wlan;
                led-upgrade = &wlan;
        };

        leds {
                compatible = "gpio-leds";

                wlan: wlan {
                        label = "gl-ar150:orange:wlan";
                        gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
                        linux,default-trigger = "phy0tpt";
                };

                lan {
                        label = "gl-ar150:green:lan";
                        gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
                };

                wan {
                        label = "gl-ar150:green:wan";
                        gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
                };
        };

        keys {
                compatible = "gpio-keys-polled";
                poll-interval = <100>;

                manual {
                        label = "manual";
                        linux,code = <BTN_7>;
                        gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
                };

                auto {
                        label = "auto";
                        linux,code = <BTN_8>;
                        gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
                };

                reset {
                        label = "reset";
                        linux,code = <KEY_RESTART>;
                        gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
                };
        };
};

&uart {
        status = "okay";
};

&gpio {
        status = "okay";
};

&usb {
        dr_mode = "host";
        status = "okay";
};

&usb_phy {
        status = "okay";
        gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
};

&spi {
        num-chipselects = <1>;
        status = "okay";

        flash@0 {
                compatible = "jedec,spi-nor";
                spi-max-frequency = <104000000>;
                reg = <0>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        partition@0 {
                                label = "u-boot";
                                reg = <0x000000 0x040000>;
                                read-only;
                        };

                        partition@1 {
                                label = "u-boot-env";
                                reg = <0x040000 0x010000>;
                        };

                        partition@2 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x050000 0xfa0000>;
                        };

                        art: partition@3 {
                                label = "ART";
                                reg = <0xff0000 0x010000>;
                                read-only;
                        };
                };
        };
};

&eth0 {
        status = "okay";

        mtd-mac-address = <&art 0x0>;
};

&eth1 {
        status = "okay";

        mtd-mac-address = <&art 0x0>;

        gmac-config {
                device = <&gmac>;

                switch-phy-addr-swap = <0>;
                switch-phy-swap = <0>;
        };
};

&wmac {
        status = "okay";
        mtd-cal-data = <&art 0x1000>;
        mtd-mac-address = <&art 0x0>;
};