OpenWrt – Rev 4
?pathlinks?
/*
* ADM5120 specific board support for LZMA decompressor
*
* Copyright (C) 2007-2008 OpenWrt.org
* Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include "config.h"
#include <stddef.h>
#define READREG(r) *(volatile unsigned int *)(r)
#define WRITEREG(r,v) *(volatile unsigned int *)(r) = v
/*
* INTC definitions
*/
#define INTC_BASE 0xB2200000
/* INTC registers */
#define INTC_REG_IRQ_DISABLE 0x0C
/*
* UART definitions
*/
#define UART0_BASE 0xB2600000
#define UART1_BASE 0xB2800000
/* UART registers */
#define UART_REG_DATA 0x00 /* Data register */
#define UART_REG_ECR 0x04 /* Error Clear register */
#define UART_REG_LCRH 0x08 /* Line Control High register */
#define UART_REG_LCRM 0x0C /* Line Control Middle register */
#define UART_REG_LCRL 0x10 /* Line Control Low register */
#define UART_REG_CTRL 0x14 /* Control register */
#define UART_REG_FLAG 0x18 /* Flag register */
/* Control register bits */
#define UART_CTRL_EN ( 1 << 0 ) /* UART enable */
/* Line Control High register bits */
#define UART_LCRH_FEN ( 1 << 4 ) /* FIFO enable */
/* Flag register bits */
#define UART_FLAG_CTS ( 1 << 0 )
#define UART_FLAG_DSR ( 1 << 1 )
#define UART_FLAG_DCD ( 1 << 2 )
#define UART_FLAG_BUSY ( 1 << 3 )
#define UART_FLAG_RXFE ( 1 << 4 ) /* RX FIFO empty */
#define UART_FLAG_TXFF ( 1 << 5 ) /* TX FIFO full */
#define UART_FLAG_RXFF ( 1 << 6 ) /* RX FIFO full */
#define UART_FLAG_TXFE ( 1 << 7 ) /* TX FIFO empty */
/*
* SWITCH definitions
*/
#define SWITCH_BASE 0xB2000000
#define SWITCH_REG_CPUP_CONF 0x0024
#define SWITCH_REG_PORT_CONF0 0x0028
#define SWITCH_REG_GPIO_CONF0 0x00B8
#define SWITCH_REG_GPIO_CONF2 0x00BC
#define SWITCH_REG_PORT0_LED 0x0100
#define SWITCH_REG_PORT1_LED 0x0104
#define SWITCH_REG_PORT2_LED 0x0108
#define SWITCH_REG_PORT3_LED 0x010C
#define SWITCH_REG_PORT4_LED 0x0110
#define SWITCH_PORTS_HW 0x3F /* Hardware Ports */
/* CPUP_CONF register bits */
#define CPUP_CONF_DCPUP ( 1 << 0 ) /* Disable CPU port */
/* PORT_CONF0 register bits */
#define PORT_CONF0_DP_SHIFT 0 /* disable port shift*/
/*
* UART routines
*/
#if defined(CONFIG_USE_UART0)
# define UART_READ(r) READREG(UART0_BASE+(r))
# define UART_WRITE(r,v) WRITEREG(UART0_BASE+(r),(v))
#else
# define UART_READ(r) READREG(UART1_BASE+(r))
# define UART_WRITE(r,v) WRITEREG(UART1_BASE+(r),(v))
#endif
static void uart_init(void)
{
#if 0
unsigned int t;
/* disable uart */
UART_WRITE(UART_REG_CTRL, 0);
/* keep current baud rate */
t = UART_READ(UART_REG_LCRM);
UART_WRITE(UART_REG_LCRM, t);
t = UART_READ(UART_REG_LCRL);
UART_WRITE(UART_REG_LCRL, t);
/* keep data, stop, and parity bits, but disable FIFO */
t = UART_READ(UART_REG_LCRH);
t &= ~(UART_LCRH_FEN);
UART_WRITE(UART_REG_LCRH, t );
/* clear error bits */
UART_WRITE(UART_REG_ECR, 0xFF);
/* enable uart, and disable interrupts */
UART_WRITE(UART_REG_CTRL, UART_CTRL_EN);
#endif
}
/*
* INTC routines
*/
#define INTC_READ(r) READREG(INTC_BASE+(r))
#define INTC_WRITE(r,v) WRITEREG(INTC_BASE+(r),v)
static void intc_init(void)
{
INTC_WRITE(INTC_REG_IRQ_DISABLE, 0xFFFFFFFF);
}
/*
* SWITCH routines
*/
#define SWITCH_READ(r) READREG(SWITCH_BASE+(r))
#define SWITCH_WRITE(r,v) WRITEREG(SWITCH_BASE+(r),v)
static void switch_init(void)
{
/* disable PHYS ports */
SWITCH_WRITE(SWITCH_REG_PORT_CONF0,
(SWITCH_PORTS_HW << PORT_CONF0_DP_SHIFT));
/* disable CPU port */
SWITCH_WRITE(SWITCH_REG_CPUP_CONF, CPUP_CONF_DCPUP);
/* disable GPIO lines */
SWITCH_WRITE(SWITCH_REG_GPIO_CONF0, 0);
SWITCH_WRITE(SWITCH_REG_GPIO_CONF2, 0);
/* disable LED lines */
SWITCH_WRITE(SWITCH_REG_PORT0_LED, 0);
SWITCH_WRITE(SWITCH_REG_PORT1_LED, 0);
SWITCH_WRITE(SWITCH_REG_PORT2_LED, 0);
SWITCH_WRITE(SWITCH_REG_PORT3_LED, 0);
SWITCH_WRITE(SWITCH_REG_PORT4_LED, 0);
}
void board_putc(int ch)
{
while ((UART_READ(UART_REG_FLAG) & UART_FLAG_TXFE) == 0);
UART_WRITE(UART_REG_DATA, ch);
while ((UART_READ(UART_REG_FLAG) & UART_FLAG_TXFE) == 0);
}
void board_init(void)
{
intc_init();
switch_init();
uart_init();
}