OpenWrt – Rev 4
?pathlinks?
#!/bin/sh
[ -n "$INCLUDE_ONLY" ] || {
. /lib/functions.sh
. ../netifd-proto.sh
init_proto "$@"
}
proto_qmi_init_config() {
available=1
no_device=1
proto_config_add_string "device:device"
proto_config_add_string apn
proto_config_add_string auth
proto_config_add_string username
proto_config_add_string password
proto_config_add_string pincode
proto_config_add_int delay
proto_config_add_string modes
proto_config_add_string pdptype
proto_config_add_int profile
proto_config_add_boolean dhcpv6
proto_config_add_boolean autoconnect
proto_config_add_int plmn
proto_config_add_int timeout
proto_config_add_defaults
}
proto_qmi_setup() {
local interface="$1"
local dataformat connstat
local device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn timeout $PROTO_DEFAULT_OPTIONS
local ip4table ip6table
local cid_4 pdh_4 cid_6 pdh_6
local ip_6 ip_prefix_length gateway_6 dns1_6 dns2_6
json_get_vars device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn ip4table ip6table timeout $PROTO_DEFAULT_OPTIONS
[ "$timeout" = "" ] && timeout="10"
[ "$metric" = "" ] && metric="0"
[ -n "$ctl_device" ] && device=$ctl_device
[ -n "$device" ] || {
echo "No control device specified"
proto_notify_error "$interface" NO_DEVICE
proto_set_available "$interface" 0
return 1
}
[ -n "$delay" ] && sleep "$delay"
device="$(readlink -f $device)"
[ -c "$device" ] || {
echo "The specified control device does not exist"
proto_notify_error "$interface" NO_DEVICE
proto_set_available "$interface" 0
return 1
}
devname="$(basename "$device")"
devpath="$(readlink -f /sys/class/usbmisc/$devname/device/)"
ifname="$( ls "$devpath"/net )"
[ -n "$ifname" ] || {
echo "The interface could not be found."
proto_notify_error "$interface" NO_IFACE
proto_set_available "$interface" 0
return 1
}
echo "Waiting for SIM initialization"
local uninitialized_timeout=0
while uqmi -s -d "$device" --get-pin-status | grep '"UIM uninitialized"' > /dev/null; do
[ -e "$device" ] || return 1
if [ "$uninitialized_timeout" -lt "$timeout" ]; then
let uninitialized_timeout++
sleep 1;
else
echo "SIM not initialized"
proto_notify_error "$interface" SIM_NOT_INITIALIZED
proto_block_restart "$interface"
return 1
fi
done
if uqmi -s -d "$device" --get-pin-status | grep '"Not supported"\|"Invalid QMI command"' > /dev/null; then
[ -n "$pincode" ] && {
uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null || {
echo "Unable to verify PIN"
proto_notify_error "$interface" PIN_FAILED
proto_block_restart "$interface"
return 1
}
}
else
. /usr/share/libubox/jshn.sh
json_load "$(uqmi -s -d "$device" --get-pin-status)"
json_get_var pin1_status pin1_status
json_get_var pin1_verify_tries pin1_verify_tries
case "$pin1_status" in
disabled)
echo "PIN verification is disabled"
;;
blocked)
echo "SIM locked PUK required"
proto_notify_error "$interface" PUK_NEEDED
proto_block_restart "$interface"
return 1
;;
not_verified)
[ "$pin1_verify_tries" -lt "3" ] && {
echo "PIN verify count value is $pin1_verify_tries this is below the limit of 3"
proto_notify_error "$interface" PIN_TRIES_BELOW_LIMIT
proto_block_restart "$interface"
return 1
}
if [ -n "$pincode" ]; then
uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null 2>&1 || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null 2>&1 || {
echo "Unable to verify PIN"
proto_notify_error "$interface" PIN_FAILED
proto_block_restart "$interface"
return 1
}
else
echo "PIN not specified but required"
proto_notify_error "$interface" PIN_NOT_SPECIFIED
proto_block_restart "$interface"
return 1
fi
;;
verified)
echo "PIN already verified"
;;
*)
echo "PIN status failed ($pin1_status)"
proto_notify_error "$interface" PIN_STATUS_FAILED
proto_block_restart "$interface"
return 1
;;
esac
fi
[ -n "$plmn" ] && {
local mcc mnc
if [ "$plmn" = 0 ]; then
mcc=0
mnc=0
echo "Setting PLMN to auto"
else
mcc=${plmn:0:3}
mnc=${plmn:3}
echo "Setting PLMN to $plmn"
fi
uqmi -s -d "$device" --set-plmn --mcc "$mcc" --mnc "$mnc" > /dev/null 2>&1 || {
echo "Unable to set PLMN"
proto_notify_error "$interface" PLMN_FAILED
proto_block_restart "$interface"
return 1
}
}
# Cleanup current state if any
uqmi -s -d "$device" --stop-network 0xffffffff --autoconnect > /dev/null 2>&1
# Set IP format
uqmi -s -d "$device" --set-data-format 802.3 > /dev/null 2>&1
uqmi -s -d "$device" --wda-set-data-format 802.3 > /dev/null 2>&1
dataformat="$(uqmi -s -d "$device" --wda-get-data-format)"
if [ "$dataformat" = '"raw-ip"' ]; then
[ -f /sys/class/net/$ifname/qmi/raw_ip ] || {
echo "Device only supports raw-ip mode but is missing this required driver attribute: /sys/class/net/$ifname/qmi/raw_ip"
return 1
}
echo "Device does not support 802.3 mode. Informing driver of raw-ip only for $ifname .."
echo "Y" > /sys/class/net/$ifname/qmi/raw_ip
fi
uqmi -s -d "$device" --sync > /dev/null 2>&1
echo "Waiting for network registration"
local registration_timeout=0
while uqmi -s -d "$device" --get-serving-system | grep '"searching"' > /dev/null; do
[ -e "$device" ] || return 1
if [ "$registration_timeout" -lt "$timeout" ]; then
let registration_timeout++
sleep 1;
else
echo "Network registration failed"
proto_notify_error "$interface" NETWORK_REGISTRATION_FAILED
proto_block_restart "$interface"
return 1
fi
done
[ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
pdptype=$(echo "$pdptype" | awk '{print tolower($0)}')
[ "$pdptype" = "ip" -o "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] || pdptype="ip"
if [ "$pdptype" = "ip" ]; then
[ -z "$autoconnect" ] && autoconnect=1
[ "$autoconnect" = 0 ] && autoconnect=""
else
[ "$autoconnect" = 1 ] || autoconnect=""
fi
[ "$pdptype" = "ip" -o "$pdptype" = "ipv4v6" ] && {
cid_4=$(uqmi -s -d "$device" --get-client-id wds)
if ! [ "$cid_4" -eq "$cid_4" ] 2> /dev/null; then
echo "Unable to obtain client ID"
proto_notify_error "$interface" NO_CID
return 1
fi
uqmi -s -d "$device" --set-client-id wds,"$cid_4" --set-ip-family ipv4 > /dev/null 2>&1
pdh_4=$(uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
--start-network \
${apn:+--apn $apn} \
${profile:+--profile $profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
${autoconnect:+--autoconnect})
# pdh_4 is a numeric value on success
if ! [ "$pdh_4" -eq "$pdh_4" ] 2> /dev/null; then
echo "Unable to connect IPv4"
uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
fi
# Check data connection state
connstat=$(uqmi -s -d "$device" --get-data-status)
[ "$connstat" == '"connected"' ] || {
echo "No data link!"
uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
}
}
[ "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] && {
cid_6=$(uqmi -s -d "$device" --get-client-id wds)
if ! [ "$cid_6" -eq "$cid_6" ] 2> /dev/null; then
echo "Unable to obtain client ID"
proto_notify_error "$interface" NO_CID
return 1
fi
uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 > /dev/null 2>&1
pdh_6=$(uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
--start-network \
${apn:+--apn $apn} \
${profile:+--profile $profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
${autoconnect:+--autoconnect})
# pdh_6 is a numeric value on success
if ! [ "$pdh_6" -eq "$pdh_6" ] 2> /dev/null; then
echo "Unable to connect IPv6"
uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
fi
# Check data connection state
connstat=$(uqmi -s -d "$device" --get-data-status)
[ "$connstat" == '"connected"' ] || {
echo "No data link!"
uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds > /dev/null 2>&1
proto_notify_error "$interface" CALL_FAILED
return 1
}
}
echo "Setting up $ifname"
proto_init_update "$ifname" 1
proto_set_keep 1
proto_add_data
[ -n "$pdh_4" ] && {
json_add_string "cid_4" "$cid_4"
json_add_string "pdh_4" "$pdh_4"
}
[ -n "$pdh_6" ] && {
json_add_string "cid_6" "$cid_6"
json_add_string "pdh_6" "$pdh_6"
}
proto_close_data
proto_send_update "$interface"
[ -n "$pdh_6" ] && {
if [ -z "$dhcpv6" -o "$dhcpv6" = 0 ]; then
json_load "$(uqmi -s -d $device --set-client-id wds,$cid_6 --get-current-settings)"
json_select ipv6
json_get_var ip_6 ip
json_get_var gateway_6 gateway
json_get_var dns1_6 dns1
json_get_var dns2_6 dns2
json_get_var ip_prefix_length ip-prefix-length
proto_init_update "$ifname" 1
proto_set_keep 1
proto_add_ipv6_address "$ip_6" "128"
proto_add_ipv6_prefix "${ip_6}/${ip_prefix_length}"
proto_add_ipv6_route "$gateway_6" "128"
[ "$defaultroute" = 0 ] || proto_add_ipv6_route "::0" 0 "$gateway_6" "" "" "${ip_6}/${ip_prefix_length}"
[ "$peerdns" = 0 ] || {
proto_add_dns_server "$dns1_6"
proto_add_dns_server "$dns2_6"
}
proto_send_update "$interface"
else
json_init
json_add_string name "${interface}_6"
json_add_string ifname "@$interface"
json_add_string proto "dhcpv6"
[ -n "$ip6table" ] && json_add_string ip6table "$ip6table"
proto_add_dynamic_defaults
# RFC 7278: Extend an IPv6 /64 Prefix to LAN
json_add_string extendprefix 1
json_close_object
ubus call network add_dynamic "$(json_dump)"
fi
}
[ -n "$pdh_4" ] && {
json_init
json_add_string name "${interface}_4"
json_add_string ifname "@$interface"
json_add_string proto "dhcp"
[ -n "$ip4table" ] && json_add_string ip4table "$ip4table"
proto_add_dynamic_defaults
json_close_object
ubus call network add_dynamic "$(json_dump)"
}
}
qmi_wds_stop() {
local cid="$1"
local pdh="$2"
[ -n "$cid" ] || return
uqmi -s -d "$device" --set-client-id wds,"$cid" \
--stop-network 0xffffffff \
--autoconnect > /dev/null 2>&1
[ -n "$pdh" ] && {
uqmi -s -d "$device" --set-client-id wds,"$cid" \
--stop-network "$pdh" > /dev/null 2>&1
}
uqmi -s -d "$device" --set-client-id wds,"$cid" \
--release-client-id wds > /dev/null 2>&1
}
proto_qmi_teardown() {
local interface="$1"
local device cid_4 pdh_4 cid_6 pdh_6
json_get_vars device
[ -n "$ctl_device" ] && device=$ctl_device
echo "Stopping network $interface"
json_load "$(ubus call network.interface.$interface status)"
json_select data
json_get_vars cid_4 pdh_4 cid_6 pdh_6
qmi_wds_stop "$cid_4" "$pdh_4"
qmi_wds_stop "$cid_6" "$pdh_6"
proto_init_update "*" 0
proto_send_update "$interface"
}
[ -n "$INCLUDE_ONLY" ] || {
add_protocol qmi
}