OpenWrt – Rev 1
?pathlinks?
From ac8fcc92d87436715ce85f39a4fe4f07c3bfa15e Mon Sep 17 00:00:00 2001
From: Luis Araneda <luaraneda@gmail.com>
Date: Sun, 22 Jul 2018 02:52:41 -0400
Subject: [U-Boot] [RFC PATCH] arm: zynq: read mac address from SPI flash memory
Implement a method for reading the MAC address from an
SPI flash memory.
In particular, this method is used by the Zybo Z7 board
to read the MAC address from the OTP region in the SPI NOR
memory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
---
As of 2018-08-23, this patch has been sent to U-Boot's mailing list
and is being reviewed. Some changes on the implementation are expected,
but the functionality should not change
---
board/xilinx/zynq/board.c | 28 ++++++++++++++++++++++++++++
configs/zynq_zybo_z7_defconfig | 3 +++
drivers/misc/Kconfig | 17 +++++++++++++++++
3 files changed, 48 insertions(+)
--- a/board/xilinx/zynq/board.c
+++ b/board/xilinx/zynq/board.c
@@ -6,9 +6,12 @@
#include <common.h>
#include <dm/uclass.h>
+#include <dm/device.h>
+#include <dm/device-internal.h>
#include <fdtdec.h>
#include <fpga.h>
#include <mmc.h>
+#include <spi_flash.h>
#include <watchdog.h>
#include <wdt.h>
#include <zynqpl.h>
@@ -83,6 +86,31 @@ int zynq_board_read_rom_ethaddr(unsigned
printf("I2C EEPROM MAC address read failed\n");
#endif
+#if defined(CONFIG_MAC_ADDR_IN_SPI_FLASH)
+ struct spi_flash *flash;
+ struct udevice *dev;
+ int ret;
+
+ ret = spi_flash_probe_bus_cs(CONFIG_SF_DEFAULT_BUS,
+ CONFIG_SF_DEFAULT_CS,
+ 0, 0, &dev);
+ if (ret) {
+ printf("SPI(bus:%u cs:%u) probe failed\n",
+ CONFIG_SF_DEFAULT_BUS,
+ CONFIG_SF_DEFAULT_CS);
+ return 0;
+ }
+
+ flash = dev_get_uclass_priv(dev);
+ flash->read_cmd = CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD;
+
+ if (spi_flash_read_dm(dev,
+ CONFIG_MAC_ADDR_SPI_FLASH_DATA_OFFSET,
+ 6, ethaddr))
+ printf("SPI MAC address read failed\n");
+
+ device_remove(dev, DM_REMOVE_NORMAL);
+#endif
return 0;
}
--- a/configs/zynq_zybo_z7_defconfig
+++ b/configs/zynq_zybo_z7_defconfig
@@ -44,6 +44,9 @@ CONFIG_DM_GPIO=y
CONFIG_SYS_I2C_ZYNQ=y
CONFIG_ZYNQ_I2C0=y
CONFIG_ZYNQ_I2C1=y
+CONFIG_MAC_ADDR_IN_SPI_FLASH=y
+CONFIG_MAC_ADDR_SPI_FLASH_READ_CMD=0x4b
+CONFIG_MAC_ADDR_SPI_FLASH_DATA_OFFSET=0x20
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
CONFIG_SPI_FLASH=y
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -272,6 +272,23 @@ config SYS_I2C_EEPROM_ADDR_OVERFLOW
endif
+config MAC_ADDR_IN_SPI_FLASH
+ bool "MAC address in SPI flash"
+ help
+ Read MAC address from an SPI flash memory
+
+if MAC_ADDR_IN_SPI_FLASH
+
+config MAC_ADDR_SPI_FLASH_READ_CMD
+ hex "Read command for the SPI flash memory"
+ default 0
+
+config MAC_ADDR_SPI_FLASH_DATA_OFFSET
+ hex "Offset of MAC data in SPI flash memory"
+ default 0
+
+endif
+
config GDSYS_RXAUI_CTRL
bool "Enable gdsys RXAUI control driver"
depends on MISC