OpenWrt – Rev 4
?pathlinks?
--- /dev/null
+++ b/board/bt/bthomehubv5a/Makefile
@@ -0,0 +1,27 @@
+#
+# Copyright (C) 2000-2011 Wolfgang Denk, DENX Software Engineering, wd@denx.de
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS = $(BOARD).o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+++ b/board/bt/bthomehubv5a/bthomehubv5a.c
@@ -0,0 +1,125 @@
+/*
+ * Copyright (C) 2015 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ * Based on p2812hnufx.c: (C) 2013 Luka Perkov <luka@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/lantiq/eth.h>
+#include <asm/lantiq/chipid.h>
+#include <asm/lantiq/cpu.h>
+#include <asm/arch/gphy.h>
+
+#if defined(CONFIG_SPL_BUILD)
+#define do_gpio_init 1
+#define do_pll_init 1
+#define do_dcdc_init 0
+#elif defined(CONFIG_SYS_BOOT_RAM)
+#define do_gpio_init 1
+#define do_pll_init 0
+#define do_dcdc_init 1
+#else
+#define do_gpio_init 0
+#define do_pll_init 0
+#define do_dcdc_init 1
+#endif
+
+#define GPIO_POWER_GREEN 14
+#define GPIO_POWER_RED 12
+
+static void gpio_init(void)
+{
+ /* EBU.FL_CS1 as output for NAND CE */
+ gpio_set_altfunc(23, GPIO_ALTSEL_SET, GPIO_ALTSEL_CLR, GPIO_DIR_OUT);
+ /* EBU.FL_A23 as output for NAND CLE */
+ gpio_set_altfunc(24, GPIO_ALTSEL_SET, GPIO_ALTSEL_CLR, GPIO_DIR_OUT);
+ /* EBU.FL_A24 as output for NAND ALE */
+ gpio_set_altfunc(13, GPIO_ALTSEL_SET, GPIO_ALTSEL_CLR, GPIO_DIR_OUT);
+ /* GPIO 3.0 as input for NAND Ready Busy */
+ gpio_set_altfunc(48, GPIO_ALTSEL_SET, GPIO_ALTSEL_CLR, GPIO_DIR_IN);
+ /* GPIO 3.1 as output for NAND Read */
+ gpio_set_altfunc(49, GPIO_ALTSEL_SET, GPIO_ALTSEL_CLR, GPIO_DIR_OUT);
+
+ /* Turn on the green power LED */
+ gpio_direction_output(GPIO_POWER_GREEN, 0);
+
+ /* Turn off the red power LED */
+ gpio_direction_output(GPIO_POWER_RED, 1);
+}
+
+int board_early_init_f(void)
+{
+ if (do_gpio_init)
+ gpio_init();
+
+ if (do_pll_init)
+ ltq_pll_init();
+
+ if (do_dcdc_init)
+ ltq_dcdc_init(0x7F);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: " CONFIG_BOARD_NAME "\n");
+ ltq_chip_print_info();
+
+ return 0;
+}
+
+void show_boot_progress(int arg)
+{
+ if (!do_gpio_init)
+ return 0;
+
+ if (arg >= 0) {
+ /* Success - turn off the red power LED and turn on the green power LED */
+ gpio_set_value(GPIO_POWER_RED, 1);
+ gpio_set_value(GPIO_POWER_GREEN, 0);
+ } else {
+ /* Failure - turn off green power LED and turn on red power LED */
+ gpio_set_value(GPIO_POWER_GREEN, 1);
+ gpio_set_value(GPIO_POWER_RED, 0);
+ }
+
+ return 0;
+}
+
+static const struct ltq_eth_port_config eth_port_config[] = {
+ /* GMAC0: external Lantiq PEF7071 10/100/1000 PHY for LAN port 3 */
+ { 0, 0x0, LTQ_ETH_PORT_PHY, PHY_INTERFACE_MODE_RGMII },
+ /* GMAC1: external Lantiq PEF7071 10/100/1000 PHY for LAN port 4 */
+ { 1, 0x1, LTQ_ETH_PORT_PHY, PHY_INTERFACE_MODE_RGMII },
+ /* GMAC2: internal GPHY0 with 10/100/1000 firmware for LAN port 2 */
+ { 2, 0x11, LTQ_ETH_PORT_PHY, PHY_INTERFACE_MODE_GMII },
+ /* GMAC3: unused */
+ { 3, 0x0, LTQ_ETH_PORT_NONE, PHY_INTERFACE_MODE_NONE },
+ /* GMAC4: internal GPHY1 with 10/100/1000 firmware for LAN port 1 */
+ { 4, 0x13, LTQ_ETH_PORT_PHY, PHY_INTERFACE_MODE_GMII },
+ /* GMAC5: external Lantiq PEF7071 10/100/1000 PHY for WANoE port */
+ { 5, 0x5, LTQ_ETH_PORT_PHY, PHY_INTERFACE_MODE_RGMII },
+};
+
+static const struct ltq_eth_board_config eth_board_config = {
+ .ports = eth_port_config,
+ .num_ports = ARRAY_SIZE(eth_port_config),
+};
+
+int board_eth_init(bd_t * bis)
+{
+ const enum ltq_gphy_clk clk = LTQ_GPHY_CLK_25MHZ_PLL0;
+ const ulong fw_addr = 0x80FE0000;
+
+ ltq_gphy_phy11g_a2x_load(fw_addr);
+
+ ltq_cgu_gphy_clk_src(clk);
+
+ ltq_rcu_gphy_boot(0, fw_addr);
+ ltq_rcu_gphy_boot(1, fw_addr);
+
+ return ltq_eth_initialize(ð_board_config);
+}
--- /dev/null
+++ b/board/bt/bthomehubv5a/config.mk
@@ -0,0 +1,7 @@
+#
+# Copyright (C) 2012-2013 Daniel Schwierzeck, daniel.schwierzeck@gmail.com
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(BOARDDIR)
--- /dev/null
+++ b/board/bt/bthomehubv5a/ddr_settings.h
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2015 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ *
+ * The values have been taken from the HH5A GPL source.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#define MC_CCR00_VALUE 0x101
+#define MC_CCR01_VALUE 0x1000101
+#define MC_CCR02_VALUE 0x1010000
+#define MC_CCR03_VALUE 0x101
+#define MC_CCR04_VALUE 0x1000000
+#define MC_CCR05_VALUE 0x1000101
+#define MC_CCR06_VALUE 0x1000100
+#define MC_CCR07_VALUE 0x1010000
+#define MC_CCR08_VALUE 0x1000101
+#define MC_CCR09_VALUE 0x0
+#define MC_CCR10_VALUE 0x2000100
+#define MC_CCR11_VALUE 0x2000401
+#define MC_CCR12_VALUE 0x30000
+#define MC_CCR13_VALUE 0x202
+#define MC_CCR14_VALUE 0x7080A0F
+#define MC_CCR15_VALUE 0x2040F
+#define MC_CCR16_VALUE 0x40000
+#define MC_CCR17_VALUE 0x70102
+#define MC_CCR18_VALUE 0x4020002
+#define MC_CCR19_VALUE 0x30302
+#define MC_CCR20_VALUE 0x8000700
+#define MC_CCR21_VALUE 0x40F020A
+#define MC_CCR22_VALUE 0x0
+#define MC_CCR23_VALUE 0xC020000
+#define MC_CCR24_VALUE 0x4401B04
+#define MC_CCR25_VALUE 0x0
+#define MC_CCR26_VALUE 0x0
+#define MC_CCR27_VALUE 0x6420000
+#define MC_CCR28_VALUE 0x0
+#define MC_CCR29_VALUE 0x0
+#define MC_CCR30_VALUE 0x798
+#define MC_CCR31_VALUE 0x0
+#define MC_CCR32_VALUE 0x0
+#define MC_CCR33_VALUE 0x650000
+#define MC_CCR34_VALUE 0x200C8
+#define MC_CCR35_VALUE 0x1D445D
+#define MC_CCR36_VALUE 0xC8
+#define MC_CCR37_VALUE 0xC351
+#define MC_CCR38_VALUE 0x0
+#define MC_CCR39_VALUE 0x141F04
+#define MC_CCR40_VALUE 0x142704
+#define MC_CCR41_VALUE 0x141b42
+#define MC_CCR42_VALUE 0x141b42
+#define MC_CCR43_VALUE 0x566504
+#define MC_CCR44_VALUE 0x566504
+#define MC_CCR45_VALUE 0x565F17
+#define MC_CCR46_VALUE 0x565F17
+#define MC_CCR47_VALUE 0x0
+#define MC_CCR48_VALUE 0x0
+#define MC_CCR49_VALUE 0x0
+#define MC_CCR50_VALUE 0x0
+#define MC_CCR51_VALUE 0x0
+#define MC_CCR52_VALUE 0x133
+#define MC_CCR53_VALUE 0xF3014B27
+#define MC_CCR54_VALUE 0xF3014B27
+#define MC_CCR55_VALUE 0xF3014B27
+#define MC_CCR56_VALUE 0xF3014B27
+#define MC_CCR57_VALUE 0x7800301
+#define MC_CCR58_VALUE 0x7800301
+#define MC_CCR59_VALUE 0x7800301
+#define MC_CCR60_VALUE 0x7800301
+#define MC_CCR61_VALUE 0x4
--- a/boards.cfg
+++ b/boards.cfg
@@ -546,6 +546,8 @@ Active mips mips32 vrx20
Active mips mips32 vrx200 avm fb3370 fb3370_eva fb3370:SYS_BOOT_EVA Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Active mips mips32 vrx200 avm fb3370 fb3370_ram fb3370:SYS_BOOT_RAM Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Active mips mips32 vrx200 avm fb3370 fb3370_sfspl fb3370:SYS_BOOT_SFSPL Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
+Active mips mips32 vrx200 bt bthomehubv5a bthomehubv5a_nandspl bthomehubv5a:SYS_BOOT_NANDSPL Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+Active mips mips32 vrx200 bt bthomehubv5a bthomehubv5a_ram bthomehubv5a:SYS_BOOT_RAM Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Active mips mips32 vrx200 lantiq easy80920 easy80920_nandspl easy80920:SYS_BOOT_NANDSPL Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Active mips mips32 vrx200 lantiq easy80920 easy80920_nor easy80920:SYS_BOOT_NOR Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Active mips mips32 vrx200 lantiq easy80920 easy80920_norspl easy80920:SYS_BOOT_NORSPL Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
--- /dev/null
+++ b/include/configs/bthomehubv5a.h
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2016 Mathias Kresin <openwrt@kresin.me>
+ * Copyright (C) 2015 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ * Based on p2812hnufx.h: (C) 2013 Luka Perkov <luka@openwrt.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MACH_TYPE "BTHOMEHUBV5A"
+#define CONFIG_IDENT_STRING " "CONFIG_MACH_TYPE
+#define CONFIG_BOARD_NAME "BT Home Hub 5A"
+
+/* Configure SoC */
+#define CONFIG_LTQ_SUPPORT_UART /* Enable ASC and UART */
+
+#define CONFIG_LTQ_SUPPORT_ETHERNET /* Enable ethernet */
+
+#define CONFIG_LTQ_SUPPORT_NAND_FLASH /* Have a ML01G100BHI00 NAND flash */
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+
+#define CONFIG_LTQ_SUPPORT_SPL_NAND_FLASH /* Build NAND flash SPL */
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_LTQ_SPL_COMP_LZO /* Compress SPL with LZO */
+#define CONFIG_LTQ_SPL_CONSOLE /* Enable SPL console */
+#define CONFIG_LTQ_SPL_MC_TUNE
+
+#define CONFIG_SYS_BOOTM_LEN 0x1000000 /* 16 MB */
+
+/* MTD devices */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT "nand0=nand-xway"
+#define MTDPARTS_DEFAULT "mtdparts=nand-xway:0x07e80000@0x100000(UBI)"
+
+/* UBI */
+#define CONFIG_RBTREE
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+/* Environment */
+#if defined(CONFIG_SYS_BOOT_NANDSPL)
+#define CONFIG_SPL_TPL_OFFS 0x800
+#define CONFIG_SPL_TPL_SIZE 0x5000
+#define CONFIG_SPL_MC_TUNE_OFFS 0x5800
+#define CONFIG_SPL_U_BOOT_OFFS 0x6000
+#define CONFIG_SPL_U_BOOT_SIZE 0x3a000
+
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_OFFSET (640 * 1024)
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
+#else
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+
+#define CONFIG_ENV_SIZE (128 * 1024)
+
+#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
+
+/* Console */
+#define CONFIG_LTQ_ADVANCED_CONSOLE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_CONSOLE_ASC 1
+#define CONFIG_CONSOLE_DEV "ttyLTQ1"
+
+/* Pull in default board configs for Lantiq XWAY VRX200 */
+#include <asm/lantiq/config.h>
+#include <asm/arch/config.h>
+
+/* Pull in default OpenWrt configs for Lantiq SoC */
+#include "openwrt-lantiq-common.h"
+
+#undef CONFIG_BOOTCOMMAND
+#define CONFIG_BOOTCOMMAND \
+ "mtdparts default; ubi part UBI; ubi read ${loadaddr} kernel; bootm ${loadaddr}"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_ENV_LANTIQ_DEFAULTS
+
+#endif /* __CONFIG_H */
Generated by GNU Enscript 1.6.5.90.