OpenWrt – Rev 4
?pathlinks?
/dts-v1/;
#include "danube.dtsi"
#include <dt-bindings/input/input.h>
/ {
compatible = "arcadyan,arv7519pw", "lantiq,xway", "lantiq,danube";
model = "Astoria Networks ARV7519PW";
chosen {
bootargs = "console=ttyLTQ0,115200";
};
aliases {
led-boot = &power;
led-failsafe = &power2;
led-running = &power;
led-dsl = &dsl;
led-internet = &online;
led-wifi = &wifi;
};
memory@0 {
reg = <0x0 0x4000000>;
};
sram@1F000000 {
vmmc@107000 {
status = "okay";
};
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x2000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x40000>;
read-only;
};
partition@40000 {
label = "uboot_env";
reg = <0x40000 0x20000>;
};
partition@60000 {
label = "firmware";
reg = <0x60000 0xf80000>;
};
boardconfig: partition@fe0000 {
label = "board_config";
reg = <0xfe0000 0x20000>;
read-only;
};
};
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
ebu {
lantiq,groups = "ebu cs1";
lantiq,function = "ebu";
};
pci_in {
lantiq,groups = "req1";
lantiq,function = "pci";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_out {
lantiq,groups = "gnt1";
lantiq,function = "pci";
lantiq,pull = <0>;
lantiq,output = <1>;
};
pci_rst {
lantiq,pins = "io21";
lantiq,pull = <2>;
lantiq,output = <1>;
};
switch_rst {
lantiq,pins = "io19";
lantiq,pull = <2>;
lantiq,output = <1>;
};
};
};
etop@E180000 {
phy-mode = "mii";
mtd-mac-address = <&boardconfig 0x16>;
};
/* warning: passive port
only works with active devices */
ifxhcd@E101000 {
status = "okay";
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
rfkill {
label = "rfkill";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
reset {
label = "reset";
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
gpio-leds {
compatible = "gpio-leds";
power: power {
label = "power";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
power2: power2 {
label = "power2";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
online: online {
label = "online";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
online2 {
label = "online2";
gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
};
wifi: wifi {
label = "wifi";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
wifi2 {
label = "wifi2";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
wifi3 {
label = "wifi3";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
voice {
label = "voice";
gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
};
wps {
label = "wps";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
wps2 {
label = "wps2";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
};
wps3 {
label = "wps3";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
};
dsl: dsl {
label = "dsl";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
lan {
label = "lan";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
};
tv {
label = "tv";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
upgrade {
label = "upgrade";
gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
};
};
/* is there another way to "reserve" the GPIO? */
gpio_export {
compatible = "gpio-export";
#size-cells = <0>;
switch {
gpio-export,name = "switch";
gpio-export,output = <1>;
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
};
};
};
&pci0 {
status = "okay";
lantiq,external-clock;
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
req-mask = <0xf>;
wifi@0,0 {
compatible = "pci0,0";
reg = <0x7000 0 0 0 0>;
ralink,mtd-eeprom = <&boardconfig 0x410>;
ralink,mtd-eeprom-swap;
};
};