OpenWrt – Rev 4
?pathlinks?
/dts-v1/;
#include "danube.dtsi"
#include <dt-bindings/input/input.h>
/ {
compatible = "arcadyan,arv7510pw22", "lantiq,xway", "lantiq,danube";
model = "Astoria Networks ARV7510PW22";
chosen {
bootargs = "console=ttyLTQ0,115200";
};
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-dsl = &internet;
led-usb = &umts;
led-wifi = &wlan;
};
memory@0 {
reg = <0x0 0x4000000>;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
rfkill {
label = "rfkill";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
restart {
label = "restart";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
};
reset {
label = "reset";
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
gpio-leds {
compatible = "gpio-leds";
power: power {
label = "power";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
internet: internet {
label = "internet";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
wlan: wlan {
label = "wlan";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
umts: 3g {
label = "3g";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
message {
label = "message";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
};
};
&gpio {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
exin {
lantiq,groups = "exin1";
lantiq,function = "exin";
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_in {
lantiq,groups = "req1", "req2";
lantiq,function = "pci";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_out {
lantiq,groups = "gnt1";
lantiq,function = "pci";
lantiq,output = <1>;
};
pci_rst {
lantiq,pins = "io21";
lantiq,pull = <2>;
lantiq,output = <1>;
};
pins_out {
lantiq,pins = "io2", "io4", "io8", "io9", "io10", "io15", "io20";
lantiq,output = <1>;
};
pins_in {
lantiq,pins = "io11", "io12", "io28";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
};
usb_vbus: regulator-usb-vbus {
compatible = "regulator-fixed";
regulator-name = "USB_VBUS";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
&gsw {
/* Switch reset 19 */
phy-mode = "mii";
mtd-mac-address = <&boardconfig 0x16>;
};
&localbus {
nor@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x1000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x40000>;
read-only;
};
partition@40000 {
label = "uboot_env";
reg = <0x40000 0x20000>;
read-only;
};
partition@60000 {
label = "firmware";
reg = <0x60000 0xf80000>;
};
boardconfig: partition@fe0000 {
label = "board_config";
reg = <0xfe0000 0x20000>;
read-only;
};
};
};
};
&pci0 {
status = "okay";
lantiq,external-clock;
interrupt-map = <
0x7000 0 0 1 &icu0 30
0x7800 0 0 1 &icu0 135
0x7800 0 0 2 &icu0 135
0x7800 0 0 3 &icu0 135
>;
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
req-mask = <0x3>;
wifi@1814,3592 {
compatible = "pci1814,3592";
reg = <0x7000 0 0 0 0>;
ralink,mtd-eeprom = <&boardconfig 0x410>;
ralink,mtd-eeprom-swap;
};
};
&usb_phy {
status = "okay";
phy-supply = <&usb_vbus>;
};
&usb {
status = "okay";
};
&vmmc {
status = "okay";
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
};