OpenWrt – Rev 3

?pathlinks?

Rev 2 – Blame – Compare with Previous – Last modification – View Log – Download

/dts-v1/;

#include "rt3883.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
        compatible = "sitecom,wlr-6000", "ralink,rt3883-soc";
        model = "Sitecom WLR-6000";

        gpio-keys-polled {
                compatible = "gpio-keys-polled";
                #address-cells = <1>;
                #size-cells = <0>;
                poll-interval = <20>;

                reset {
                        label = "reset";
                        gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
                        linux,code = <KEY_RESTART>;
                };
        };

        gpio-leds {
                compatible = "gpio-leds";

                power {
                        label = "wlr-6000:red:power";
                        gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
                };

                ops {
                        label = "wlr-6000:white:ops";
                        gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
                };
        };

        gpio_export {
                compatible = "gpio-export";
                #size-cells = <0>;

                usb {
                        gpio-export,name = "usb";
                        gpio-export,output = <1>;
                        gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
                };
        };
};

&gpio1 {
        status = "okay";
};

&pinctrl {
        state_default: pinctrl0 {
                gpio {
                        ralink,group = "i2c", "jtag", "uartf";
                        ralink,function = "gpio";
                };
        };
};

&ethernet {
        status = "okay";
        mtd-mac-address = <&factory 0x8004>;
        mtd-mac-address-increment = <1>;

        port@0 {
                phy-handle = <&phy0>;
                phy-mode = "rgmii";
        };

        mdio-bus {
                status = "okay";

                phy0: ethernet-phy@0 {
                        reg = <0>;
                        phy-mode = "rgmii";

                        qca,ar8327-initvals = <
                                0x04 0x07600000 /* PORT0 PAD MODE CTRL */
                                0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
                                0x10 0x40000000 /* Power-on Strapping: 176-pin interface configuration */
                                0x50 0xc437c437 /* LED Control Register 0 */
                                0x54 0xc337c337 /* LED Control Register 1 */
                                0x58 0x00000000 /* LED Control Register 2 */
                                0x5c 0x03ffff00 /* LED Control Register 3 */
                                0x7c 0x0000007e /* PORT0_STATUS */
                                0x94 0x0000007e /* PORT6 STATUS */
                        >;
                };
        };
};

&spi0 {
        status = "okay";

        m25p80@0 {
                #address-cells = <1>;
                #size-cells = <1>;
                compatible = "jedec,spi-nor";
                reg = <0>;
                spi-max-frequency = <8600000>;
                m25p,fast-read;

                partition@0 {
                        label = "u-boot";
                        reg = <0x0 0x30000>;
                        read-only;
                };

                partition@30000 {
                        label = "u-boot-env";
                        reg = <0x30000 0x10000>;
                        read-only;
                };

                factory: partition@40000 {
                        label = "factory";
                        reg = <0x40000 0x10000>;
                        read-only;
                };

                partition@50000 {
                        label = "firmware";
                        reg = <0x50000 0x713000>;
                };

                partition@763000 {
                        label = "manufacture";
                        reg = <0x763000 0x7D000>;
                        read-only;
                };

                partition@7E0000 {
                        label = "backup";
                        reg = <0x7E0000 0x10000>;
                        read-only;
                };

                partition@7F0000 {
                        label = "storage";
                        reg = <0x7F0000 0x10000>;
                        read-only;
                };
        };
};

&pci {
        status = "okay";
        pinctrl-names = "default";
        pinctrl-0 = <&pci_pins>;

        pci_pins: pci {
                pci {
                        ralink,group = "pci";
                        ralink,function = "pci-fnc";
                };
        };

        host-bridge {
                pci-bridge@1 {
                        status = "okay";

                        wifi@1814,3091 {
                                compatible = "pci1814,3091";
                                reg = <0x10000 0 0 0 0>;
                                ralink,mtd-eeprom = <&factory 0x8000>;
                        };
                };
        };
};

&wmac {
        status = "okay";
        ralink,2ghz = <0>;
        ralink,mtd-eeprom = <&factory 0x0>;
};

&ehci {
        status = "okay";
};

&ohci {
        status = "okay";
};