OpenWrt – Rev 1

Subversion Repositories:
Rev:
/dts-v1/;

#include "rt3050.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
        compatible = "belkin,f5d8235-v2", "ralink,rt3052-soc";
        model = "Belkin F5D8235 v2";

        aliases {
                led-boot = &led_router;
                led-failsafe = &led_router;
                led-running = &led_router;
                led-upgrade = &led_router;
        };

        cfi@1f000000 {
                compatible = "cfi-flash";
                reg = <0x1f000000 0x800000>;
                bank-width = <2>;
                device-width = <2>;

                partitions {
                        compatible = "fixed-partitions";
                        #address-cells = <1>;
                        #size-cells = <1>;

                        uboot: partition@0 {
                                label = "uboot";
                                reg = <0x0 0x50000>;
                                read-only;
                        };

                        partition@50000 {
                                compatible = "denx,uimage";
                                label = "firmware";
                                reg = <0x50000 0x790000>;
                        };

                        partition@7e0000 {
                                label = "nvram";
                                reg = <0x7e0000 0x10000>;
                        };

                        factory: partition@7f0000 {
                                label = "factory";
                                reg = <0x7f0000 0x10000>;
                        };
                };
        };

        rtl8366rb {
                compatible = "realtek,rtl8366rb";
                gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
                gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
        };

        leds {
                compatible = "gpio-leds";

                internet {
                        label = "f5d8235-v2:blue:internet";
                        gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
                };

                internet2 {
                        label = "f5d8235-v2:amber:internet";
                        gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
                };

                modem {
                        label = "f5d8235-v2:blue:modem";
                        gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
                };

                modem2 {
                        label = "f5d8235-v2:amber:modem";
                        gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
                };

                led_router: router {
                        label = "f5d8235-v2:blue:router";
                        gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
                };

                storage {
                        label = "f5d8235-v2:blue:storage";
                        gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
                        trigger-sources = <&otg_port1>;
                        linux,default-trigger = "usbport";
                };

                storage2 {
                        label = "f5d8235-v2:amber:storage";
                        gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
                };

                security {
                        label = "f5d8235-v2:blue:security";
                        gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
                };

                security2 {
                        label = "f5d8235-v2:amber:security";
                        gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
                };
        };
};

&pinctrl {
        state_default: pinctrl0 {
                gpio {
                        ralink,group = "spi", "i2c", "jtag", "mdio", "uartf";
                        ralink,function = "gpio";
                };
        };
};

&ethernet {
        mtd-mac-address = <&uboot 0x40004>;
        pinctrl-names = "default";
        pinctrl-0 = <&rgmii_pins>;
};

&esw {
        ralink,rgmii = <1>;
        mediatek,portmap = <0x3f>;
        ralink,fct2 = <0x0002500c>;
        /*
         * ext phy base addr 31, rx/tx clock skew 0,
         * turbo mii off, rgmi 3.3v off, port 5 polling off
         * port5: enabled, gige, full-duplex, rx/tx-flow-control
         * port6: enabled, gige, full-duplex, rx/tx-flow-control
        */
        ralink,fpa2 = <0x1f003fff>;
};

&wmac {
        ralink,mtd-eeprom = <&uboot 0x40000>;
};

&otg {
        status = "okay";
};