OpenWrt – Rev 3
?pathlinks?
/*
* jjPlus JWAP230 board support
*
* Copyright (C) 2016 Piotr Dymacz <pepe2k@gmail.com>
*
* Based on mach-wpj558.c and mach-tl-wr1043nd-v2.c
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/pci.h>
#include <linux/phy.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/ar8216_platform.h>
#include <asm/mach-ath79/ath79.h>
#include <asm/mach-ath79/ar71xx_regs.h>
#include "common.h"
#include "dev-ap9x-pci.h"
#include "dev-eth.h"
#include "dev-leds-gpio.h"
#include "dev-m25p80.h"
#include "dev-usb.h"
#include "dev-wmac.h"
#include "machtypes.h"
#include "pci.h"
#define JWAP230_GPIO_LED_LED1 23
#define JWAP230_GPIO_LED_LED2 22
#define JWAP230_GPIO_LED_LED3 21
#define JWAP230_MAC0_OFFSET 0x0
#define JWAP230_MAC1_OFFSET 0x6
#define JWAP230_WMAC_CALDATA_OFFSET 0x1000
static struct gpio_led jwap230_leds_gpio[] __initdata = {
{
.name = "jwap230:green:led1",
.gpio = JWAP230_GPIO_LED_LED1,
.active_low = 1,
},
{
.name = "jwap230:green:led2",
.gpio = JWAP230_GPIO_LED_LED2,
.active_low = 1,
},
{
.name = "jwap230:green:led3",
.gpio = JWAP230_GPIO_LED_LED3,
.active_low = 1,
}
};
static const struct ar8327_led_info jwap230_leds_qca8337[] = {
AR8327_LED_INFO(PHY0_0, HW, "jwap230:green:lan"),
AR8327_LED_INFO(PHY4_0, HW, "jwap230:green:wan"),
};
/* Blink rate: 1 Gbps -> 8 hz, 100 Mbs -> 4 Hz, 10 Mbps -> 2 Hz */
static struct ar8327_led_cfg jwap230_qca8337_led_cfg = {
.led_ctrl0 = 0xcf37cf37,
.led_ctrl1 = 0xcf37cf37,
.led_ctrl2 = 0xcf37cf37,
.led_ctrl3 = 0x0,
.open_drain = true,
};
/* QCA8337 GMAC0 is connected with QCA9558 over RGMII */
static struct ar8327_pad_cfg jwap230_qca8337_pad0_cfg = {
.mode = AR8327_PAD_MAC_RGMII,
.txclk_delay_en = true,
.rxclk_delay_en = true,
.txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
.mac06_exchange_dis = true,
};
/* QCA8337 GMAC6 is connected with QCA9558 over SGMII */
static struct ar8327_pad_cfg jwap230_qca8337_pad6_cfg = {
.mode = AR8327_PAD_MAC_SGMII,
.sgmii_delay_en = true,
.rxclk_delay_sel = AR8327_CLK_DELAY_SEL0,
};
static struct ar8327_platform_data jwap230_qca8337_data = {
.pad0_cfg = &jwap230_qca8337_pad0_cfg,
.pad6_cfg = &jwap230_qca8337_pad6_cfg,
.port0_cfg = {
.force_link = 1,
.speed = AR8327_PORT_SPEED_1000,
.duplex = 1,
.txpause = 1,
.rxpause = 1,
},
.port6_cfg = {
.force_link = 1,
.speed = AR8327_PORT_SPEED_1000,
.duplex = 1,
.txpause = 1,
.rxpause = 1,
},
.led_cfg = &jwap230_qca8337_led_cfg,
.num_leds = ARRAY_SIZE(jwap230_leds_qca8337),
.leds = jwap230_leds_qca8337,
};
static struct mdio_board_info jwap230_mdio0_info[] = {
{
.bus_id = "ag71xx-mdio.0",
.phy_addr = 0,
.platform_data = &jwap230_qca8337_data,
},
};
static void __init jwap230_setup(void)
{
u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
ath79_register_leds_gpio(-1, ARRAY_SIZE(jwap230_leds_gpio),
jwap230_leds_gpio);
mdiobus_register_board_info(jwap230_mdio0_info,
ARRAY_SIZE(jwap230_mdio0_info));
ath79_register_mdio(0, 0x0);
ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN);
/* QCA9558 GMAC0 is connected to RMGII interface */
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ath79_eth0_data.phy_mask = BIT(0);
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_eth0_pll_data.pll_1000 = 0xa6000000;
ath79_init_mac(ath79_eth0_data.mac_addr, art + JWAP230_MAC0_OFFSET, 0);
ath79_register_eth(0);
/* QCA9558 GMAC1 is connected to SGMII interface */
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
ath79_eth1_data.speed = SPEED_1000;
ath79_eth1_data.duplex = DUPLEX_FULL;
ath79_eth1_pll_data.pll_1000 = 0x03000101;
ath79_init_mac(ath79_eth1_data.mac_addr, art + JWAP230_MAC1_OFFSET, 0);
ath79_register_eth(1);
ath79_register_wmac(art + JWAP230_WMAC_CALDATA_OFFSET, NULL);
ath79_register_pci();
ath79_register_usb();
}
MIPS_MACHINE(ATH79_MACH_JWAP230, "JWAP230", "jjPlus JWAP230", jwap230_setup);