OpenWrt – Diff between revs 2 and 3
?pathlinks?
Rev 2 | Rev 3 | |||
---|---|---|---|---|
Line 7... | Line 7... | |||
7 | |
7 | |
|
8 | / { |
8 | / { |
|
9 | compatible = "jcg,jhr-n926r", "ralink,rt3052-soc"; |
9 | compatible = "jcg,jhr-n926r", "ralink,rt3052-soc"; |
|
Line 10... | Line -... | |||
10 | model = "JCG JHR-N926R"; |
- | ||
11 | |
- | ||
12 | aliases { |
- | ||
13 | led-boot = &led_system; |
- | ||
14 | led-failsafe = &led_system; |
- | ||
15 | led-running = &led_system; |
- | ||
16 | led-upgrade = &led_system; |
- | ||
17 | }; |
10 | model = "JCG JHR-N926R"; |
|
18 | |
11 | |
|
19 | cfi@1f000000 { |
12 | cfi@1f000000 { |
|
20 | compatible = "cfi-flash"; |
13 | compatible = "cfi-flash"; |
|
21 | reg = <0x1f000000 0x800000>; |
14 | reg = <0x1f000000 0x800000>; |
|
- | 15 | bank-width = <2>; |
||
- | 16 | device-width = <2>; |
||
Line 22... | Line -... | |||
22 | bank-width = <2>; |
- | ||
23 | device-width = <2>; |
- | ||
24 | |
- | ||
25 | partitions { |
- | ||
26 | compatible = "fixed-partitions"; |
- | ||
27 | #address-cells = <1>; |
17 | #address-cells = <1>; |
|
28 | #size-cells = <1>; |
18 | #size-cells = <1>; |
|
29 | |
19 | |
|
30 | partition@0 { |
20 | partition@0 { |
|
31 | label = "u-boot"; |
21 | label = "u-boot"; |
|
32 | reg = <0x0 0x30000>; |
22 | reg = <0x0 0x30000>; |
|
33 | read-only; |
23 | read-only; |
|
34 | }; |
24 | }; |
|
35 | |
25 | |
|
36 | partition@30000 { |
26 | partition@30000 { |
|
37 | label = "u-boot-env"; |
27 | label = "u-boot-env"; |
|
38 | reg = <0x30000 0x10000>; |
28 | reg = <0x30000 0x10000>; |
|
39 | read-only; |
29 | read-only; |
|
40 | }; |
30 | }; |
|
41 | |
31 | |
|
42 | factory: partition@40000 { |
32 | factory: partition@40000 { |
|
43 | label = "factory"; |
33 | label = "factory"; |
|
44 | reg = <0x40000 0x10000>; |
34 | reg = <0x40000 0x10000>; |
|
45 | read-only; |
35 | read-only; |
|
46 | }; |
- | ||
47 | |
36 | }; |
|
48 | partition@50000 { |
37 | |
|
49 | compatible = "denx,uimage"; |
- | ||
50 | label = "firmware"; |
38 | partition@50000 { |
|
51 | reg = <0x50000 0x3b0000>; |
39 | label = "firmware"; |
|
Line 52... | Line 40... | |||
52 | }; |
40 | reg = <0x50000 0x3b0000>; |
|
53 | }; |
41 | }; |
|
Line 54... | Line 42... | |||
54 | }; |
42 | }; |
|
55 | |
43 | |
|
56 | leds { |
44 | gpio-leds { |
|
Line 69... | Line 57... | |||
69 | wlan3 { |
57 | wlan3 { |
|
70 | label = "jhr-n926r:green:wlan"; |
58 | label = "jhr-n926r:green:wlan"; |
|
71 | gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; |
59 | gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; |
|
72 | }; |
60 | }; |
|
Line 73... | Line 61... | |||
73 | |
61 | |
|
74 | led_system: system { |
62 | system { |
|
75 | label = "jhr-n926r:blue:system"; |
63 | label = "jhr-n926r:blue:system"; |
|
76 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
64 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
|
77 | }; |
65 | }; |
|
Line 98... | Line 86... | |||
98 | gpio-export,output = <1>; |
86 | gpio-export,output = <1>; |
|
99 | gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; |
87 | gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; |
|
100 | }; |
88 | }; |
|
101 | }; |
89 | }; |
|
Line 102... | Line 90... | |||
102 | |
90 | |
|
103 | keys { |
91 | gpio-keys-polled { |
|
- | 92 | compatible = "gpio-keys-polled"; |
||
- | 93 | #address-cells = <1>; |
||
104 | compatible = "gpio-keys-polled"; |
94 | #size-cells = <0>; |
|
Line 105... | Line 95... | |||
105 | poll-interval = <20>; |
95 | poll-interval = <20>; |
|
106 | |
96 | |
|
107 | reset_wps { |
97 | reset_wps { |