OpenWrt – Diff between revs 2 and 3
?pathlinks?
Rev 2 | Rev 3 | |||
---|---|---|---|---|
Line 7... | Line 7... | |||
7 | |
7 | |
|
8 | / { |
8 | / { |
|
9 | compatible = "dlink,dcs-930", "ralink,rt3050-soc"; |
9 | compatible = "dlink,dcs-930", "ralink,rt3050-soc"; |
|
Line 10... | Line -... | |||
10 | model = "D-Link DCS-930"; |
- | ||
11 | |
- | ||
12 | aliases { |
- | ||
13 | led-boot = &led_status; |
- | ||
14 | led-failsafe = &led_status; |
- | ||
15 | led-running = &led_status; |
- | ||
16 | led-upgrade = &led_status; |
- | ||
17 | }; |
10 | model = "D-Link DCS-930"; |
|
18 | |
11 | |
|
19 | cfi@1f000000 { |
12 | cfi@1f000000 { |
|
20 | compatible = "cfi-flash"; |
13 | compatible = "cfi-flash"; |
|
21 | reg = <0x1f000000 0x400000>; |
14 | reg = <0x1f000000 0x400000>; |
|
- | 15 | bank-width = <2>; |
||
- | 16 | device-width = <2>; |
||
- | 17 | #address-cells = <1>; |
||
- | 18 | #size-cells = <1>; |
||
- | 19 | |
||
- | 20 | partition@0 { |
||
- | 21 | label = "u-boot"; |
||
- | 22 | reg = <0x0 0x30000>; |
||
- | 23 | read-only; |
||
- | 24 | }; |
||
- | 25 | |
||
- | 26 | partition@30000 { |
||
- | 27 | label = "u-boot-env"; |
||
- | 28 | reg = <0x30000 0x10000>; |
||
- | 29 | read-only; |
||
- | 30 | }; |
||
- | 31 | |
||
- | 32 | factory: partition@40000 { |
||
- | 33 | label = "factory"; |
||
- | 34 | reg = <0x40000 0x10000>; |
||
- | 35 | read-only; |
||
- | 36 | }; |
||
- | 37 | |
||
- | 38 | partition@50000 { |
||
- | 39 | label = "kernel"; |
||
- | 40 | reg = <0x50000 0x150000>; |
||
- | 41 | }; |
||
- | 42 | |
||
- | 43 | partition@150000 { |
||
- | 44 | label = "rootfs"; |
||
Line 22... | Line 45... | |||
22 | bank-width = <2>; |
45 | reg = <0x150000 0x2b0000>; |
|
23 | device-width = <2>; |
- | ||
24 | |
- | ||
25 | partitions { |
- | ||
26 | compatible = "fixed-partitions"; |
- | ||
27 | #address-cells = <1>; |
- | ||
28 | #size-cells = <1>; |
- | ||
29 | |
- | ||
30 | partition@0 { |
- | ||
31 | label = "u-boot"; |
- | ||
32 | reg = <0x0 0x30000>; |
- | ||
33 | read-only; |
- | ||
34 | }; |
- | ||
35 | |
- | ||
36 | partition@30000 { |
- | ||
37 | label = "u-boot-env"; |
- | ||
38 | reg = <0x30000 0x10000>; |
- | ||
39 | read-only; |
- | ||
40 | }; |
- | ||
41 | |
- | ||
42 | factory: partition@40000 { |
- | ||
43 | label = "factory"; |
- | ||
44 | reg = <0x40000 0x10000>; |
- | ||
45 | read-only; |
- | ||
46 | }; |
- | ||
47 | |
46 | }; |
|
48 | partition@50000 { |
47 | |
|
49 | compatible = "denx,uimage"; |
- | ||
50 | label = "firmware"; |
48 | partition { |
|
51 | reg = <0x50000 0x3b0000>; |
49 | label = "firmware"; |
|
Line 52... | Line 50... | |||
52 | }; |
50 | reg = <0x50000 0x3b0000>; |
|
53 | }; |
51 | }; |
|
Line 54... | Line 52... | |||
54 | }; |
52 | }; |
|
55 | |
53 | |
|
56 | leds { |
54 | gpio-leds { |
|
57 | compatible = "gpio-leds"; |
55 | compatible = "gpio-leds"; |
|
Line 58... | Line 56... | |||
58 | |
56 | |
|
59 | wifi { |
57 | wifi { |
|
60 | label = "dcs-930:red:alert"; |
58 | label = "dcs-930:red:alert"; |
|
61 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
59 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
|
Line 62... | Line 60... | |||
62 | }; |
60 | }; |
|
63 | |
61 | |
|
64 | led_status: status { |
62 | power { |
|
65 | label = "dcs-930:green:status"; |
63 | label = "dcs-930:green:status"; |
|
66 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
64 | gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
|
Line 67... | Line 65... | |||
67 | }; |
65 | }; |
|
68 | |
66 | |
|
- | 67 | wps { |
||
- | 68 | label = "dcs-930:blue:wps"; |
||
69 | wps { |
69 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
|
Line 70... | Line 70... | |||
70 | label = "dcs-930:blue:wps"; |
70 | }; |
|
71 | gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
71 | }; |
|
72 | }; |
72 | |