OpenWrt – Diff between revs 2 and 3

Subversion Repositories:
Rev:
Show entire file – Ignore whitespace
Rev 2 Rev 3
Line 7... Line 7...
7 * any warranty of any kind, whether express or implied. 7 * any warranty of any kind, whether express or implied.
8 */ 8 */
Line 9... Line 9...
9   9  
Line 10... Line 10...
10 /dts-v1/; 10 /dts-v1/;
Line 11... Line 11...
11   11  
12 #include "apm82181.dtsi" 12 #include "apollo3g.dtsi"
13   13  
14 / { -  
15 compatible = "wd,mybooklive", "amcc,apollo3g"; -  
16 model = "MyBook Live"; -  
17   -  
18 aliases { -  
19 serial0 = &UART0; -  
20 led-boot = &status; -  
21 led-failsafe = &status; -  
22 led-running = &status; -  
23 led-upgrade = &status; -  
24 }; -  
25 }; -  
26   -  
27 &POB0 { -  
28 ebc { -  
29 nor_flash@0,0 { -  
30 status = "okay"; -  
31 compatible = "amd,s29gl512n", "jedec-probe", "cfi-flash", "mtd-rom"; -  
32 bank-width = <1>; -  
33 reg = <0x00000000 0x00000000 0x00080000>; -  
34 #address-cells = <1>; -  
35 #size-cells = <1>; -  
36   -  
37 partition@0 { -  
38 /* Part of bootrom - Don't use it without a jump */ -  
39 label = "free"; -  
40 reg = <0x00000000 0x0001e000>; -  
41 }; -  
42   -  
43 partition@1e000 { -  
44 label = "env"; -  
45 reg = <0x0001e000 0x00002000>; -  
46 }; -  
47   -  
48 partition@20000 { -  
49 label = "uboot"; -  
50 reg = <0x00020000 0x00050000>; -  
51 }; -  
52 }; -  
53 }; -  
54   -  
55 GPIO1: gpio@e0000000 { -  
56 compatible = "wd,mbl-gpio", "ti,74273"; -  
57 reg-names = "dat"; -  
58 reg = <0xe0000000 0x1>; -  
59 #gpio-cells = <2>; -  
60 gpio-controller; -  
61   -  
62 enable-button { -  
63 /* Defined in u-boot as: NOT_NOR -  
64 * "enables features other than NOR -  
65 * specifically, the buffer at CS2" -  
66 * (button). -  
67 * -  
68 * Note: This option is disabled as -  
69 * it prevents the system from being -  
70 * rebooted successfully. -  
71 */ -  
72   -  
73 gpio-hog; -  
74 line-name = "Enable Reset Button, disable NOR"; -  
75 gpios = <1 GPIO_ACTIVE_HIGH>; -  
76 output-low; -  
77 }; -  
78 }; -  
79   -  
80 GPIO2: gpio@e0100000 { -  
81 compatible = "wd,mbl-gpio", "ti,74244"; -  
82 reg-names = "dat"; -  
83 reg = <0xe0100000 0x1>; -  
84 #gpio-cells = <2>; -  
85 gpio-controller; -  
86 no-output; -  
87 }; -  
88   -  
89 leds { -  
90 compatible = "gpio-leds"; -  
91   -  
92 failsafe: power-red { -  
93 label = "mbl:red:power"; -  
94 gpios = <&GPIO1 4 GPIO_ACTIVE_HIGH>; -  
95 linux,default-trigger = "panic"; -  
96 }; -  
97   -  
98 status: power-green { -  
99 label = "mbl:green:power"; -  
100 gpios = <&GPIO1 5 GPIO_ACTIVE_HIGH>; -  
101 }; -  
102   -  
103 power-blue { -  
104 label = "mbl:blue:power"; -  
105 gpios = <&GPIO1 6 GPIO_ACTIVE_HIGH>; -  
106 linux,default-trigger = "disk-activity"; -  
107 }; -  
108 }; -  
109   -  
110 keys { -  
111 compatible = "gpio-keys-polled"; -  
112 poll-interval = <60>; /* 3 * 20 = 60ms */ -  
113 autorepeat; -  
114   -  
115 reset-button { -  
116 label = "Reset button"; -  
117 linux,code = <KEY_RESTART>; -  
118 gpios = <&GPIO2 2 GPIO_ACTIVE_LOW>; -  
119 }; -  
120 }; -  
121   -  
122 usbpwr: usb-regulator { -  
123 compatible = "regulator-fixed"; -  
124 regulator-name = "Power USB Core"; -  
125 gpios = <&GPIO1 2 GPIO_ACTIVE_LOW>; -  
126 regulator-min-microvolt = <5000000>; -  
127 regulator-max-microvolt = <5000000>; -  
128 }; -  
129   -  
130 sata1pwr: sata1-regulator { -  
131 compatible = "regulator-fixed"; -  
132 regulator-name = "Power Drive Port 1"; -  
133 gpios = <&GPIO1 3 GPIO_ACTIVE_LOW>; -  
134 regulator-min-microvolt = <12000000>; -  
135 regulator-max-microvolt = <12000000>; -  
136 regulator-always-on; /* needed to read OS from HDD */ -  
137 }; -  
138   -  
139 sata0pwr: sata0-regulator { -  
140 compatible = "regulator-fixed"; -  
141 regulator-name = "Power Drive Port 0"; -  
142 gpios = <&GPIO1 7 GPIO_ACTIVE_LOW>; -  
143 regulator-min-microvolt = <12000000>; -  
144 regulator-max-microvolt = <12000000>; -  
145 regulator-always-on; /* needed to read OS from HDD */ -  
146 }; -  
147 }; -  
148   -  
149 &EMAC0 { -  
150 status = "okay"; -  
151   -  
152 phy-map = <0x2>; -  
153 phy-address = <0x1>; -  
154 phy-handle = <&phy>; -  
155   -  
156 mdio { -  
157 #address-cells = <1>; -  
158 #size-cells = <0>; -  
159 reset-gpios = <&GPIO1 0 GPIO_ACTIVE_LOW>; -  
160   -  
161 phy: phy@1 { -  
162 compatible = "ethernet-phy-ieee802.3-c22"; -  
163 reg = <1>; -  
164 }; -  
165 }; -  
166 }; -  
167   -  
168 &CRYPTO { -  
169 status = "okay"; -  
170 }; -  
171   -  
172 &PKA { -  
173 status = "okay"; -  
174 }; -  
175   -  
176 &TRNG { -  
177 status = "okay"; -  
178 }; -  
179   -  
180 &SATA0 { -  
181 status = "okay"; -  
182 }; -  
183   -  
184 &SATA1 { -  
185 status = "okay"; -  
186 }; -  
187   -  
188 &UART0 { -  
189 status = "okay"; -  
190 }; -  
191   -  
192 &USBOTG0 { -  
193 status = "okay"; 14 / {