OpenWrt – Diff between revs 2 and 3
?pathlinks?
| Rev 2 | Rev 3 | |||
|---|---|---|---|---|
| Line 7... | Line 7... | |||
| 7 | |
7 | |
|
| 8 | / { |
8 | / { |
|
| 9 | compatible = "sparklan,wcr150gn", "ralink,rt3050-soc"; |
9 | compatible = "sparklan,wcr150gn", "ralink,rt3050-soc"; |
|
| Line 10... | Line -... | |||
| 10 | model = "Sparklan WCR-150GN"; |
- | ||
| 11 | |
- | ||
| 12 | aliases { |
- | ||
| 13 | led-boot = &led_power; |
- | ||
| 14 | led-failsafe = &led_power; |
- | ||
| 15 | led-running = &led_power; |
- | ||
| 16 | led-upgrade = &led_power; |
- | ||
| 17 | }; |
10 | model = "Sparklan WCR-150GN"; |
|
| 18 | |
11 | |
|
| 19 | cfi@1f000000 { |
12 | cfi@1f000000 { |
|
| 20 | compatible = "cfi-flash"; |
13 | compatible = "cfi-flash"; |
|
| 21 | reg = <0x1f000000 0x800000>; |
14 | reg = <0x1f000000 0x800000>; |
|
| 22 | bank-width = <2>; |
- | ||
| 23 | device-width = <2>; |
- | ||
| 24 | |
- | ||
| 25 | partitions { |
15 | bank-width = <2>; |
|
| 26 | compatible = "fixed-partitions"; |
16 | device-width = <2>; |
|
| Line 27... | Line 17... | |||
| 27 | #address-cells = <1>; |
17 | #address-cells = <1>; |
|
| 28 | #size-cells = <1>; |
18 | #size-cells = <1>; |
|
| Line 44... | Line 34... | |||
| 44 | reg = <0x40000 0x10000>; |
34 | reg = <0x40000 0x10000>; |
|
| 45 | read-only; |
35 | read-only; |
|
| 46 | }; |
36 | }; |
|
| Line 47... | Line 37... | |||
| 47 | |
37 | |
|
| 48 | partition@50000 { |
- | ||
| 49 | compatible = "denx,uimage"; |
38 | partition@50000 { |
|
| 50 | label = "firmware"; |
39 | label = "firmware"; |
|
| 51 | reg = <0x50000 0x3b0000>; |
40 | reg = <0x50000 0x3b0000>; |
|
| 52 | }; |
41 | }; |
|
| 53 | }; |
- | ||
| Line 54... | Line 42... | |||
| 54 | }; |
42 | }; |
|
| 55 | |
43 | |
|
| Line 56... | Line 44... | |||
| 56 | leds { |
44 | gpio-leds { |
|
| 57 | compatible = "gpio-leds"; |
45 | compatible = "gpio-leds"; |
|
| 58 | |
46 | |
|
| 59 | user { |
- | ||
| 60 | label = "wcr-150gn:amber:user"; |
- | ||
| 61 | gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
47 | user { |
|
| Line 62... | Line 48... | |||
| 62 | trigger-sources = <&otg_port1>; |
48 | label = "wcr-150gn:amber:user"; |
|
| 63 | linux,default-trigger = "usbport"; |
49 | gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
|
| 64 | }; |
50 | }; |
|
| 65 | |
51 | |
|
| 66 | led_power: power { |
52 | power { |
|
| Line 67... | Line 53... | |||
| 67 | label = "wcr-150gn:amber:power"; |
53 | label = "wcr-150gn:amber:power"; |
|
| 68 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
54 | gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
|
| - | 55 | }; |
||
| - | 56 | }; |
||
| 69 | }; |
57 | |
|
| Line 70... | Line 58... | |||
| 70 | }; |
58 | gpio-keys-polled { |
|
| 71 | |
59 | compatible = "gpio-keys-polled"; |
|
| 72 | keys { |
60 | #address-cells = <1>; |
|