| /branches/gl-inet/target/linux/lantiq/files-4.9/arch/mips/boot/dts/BTHOMEHUBV3A.dts |
|---|
| @@ -0,0 +1,208 @@ |
|---|
| /dts-v1/; |
| |
| #include "ar9.dtsi" |
| |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| compatible = "bt,homehub-v3a", "lantiq,xway", "lantiq,ar9"; |
| model = "BT Home Hub 3A"; /* SoC: Lantiq ar9 @ 333MHz */ |
| |
| chosen { |
| bootargs = "console=ttyLTQ0,115200"; |
| }; |
| |
| aliases { |
| led-boot = &power_orange; |
| led-failsafe = &power_red; |
| led-running = &power_blue; |
| |
| led-dsl = &broadband_blue; |
| led-wifi = &wireless_blue; |
| }; |
| |
| memory@0 { /* RAM: Samsung K4H511638F-LC 64MB */ |
| reg = <0x0 0x4000000>; |
| }; |
| |
| sram@1F000000 { |
| vmmc@107000 { |
| status = "okay"; |
| gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| fpi@10000000 { |
| localbus@0 { |
| nand-parts@0 { /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */ |
| compatible = "lantiq,nand-xway"; |
| lantiq,cs = <1>; |
| bank-width = <2>; |
| reg = <1 0x0 0x2000000 >; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| req-mask = <0x1>; /* PCI request lines to mask during NAND access */ |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "preboot"; |
| reg = <0x00000 0x8000>; |
| read-only; |
| }; |
| partition@8000 { |
| label = "u-boot"; |
| reg = <0x8000 0x05c000>; |
| read-only; |
| }; |
| partition@64000 { |
| label = "uboot_env"; |
| reg = <0x64000 0x004000>; |
| }; |
| ath9k_cal: partition@68000 { |
| label = "art-copy"; |
| reg = <0x68000 0x004000>; |
| }; |
| partition@6c000 { |
| label = "kernel"; |
| reg = <0x6c000 0x200000>; |
| }; |
| partition@26c000 { |
| label = "ubi"; |
| reg = <0x26c000 0x1d94000>; |
| }; |
| }; |
| }; |
| }; |
| |
| gpio: pinmux@E100B10 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&state_default>; |
| |
| state_default: pinmux { |
| nand_out { |
| lantiq,groups = "nand cle", "nand ale"; |
| lantiq,function = "ebu"; |
| lantiq,output = <1>; |
| lantiq,open-drain = <0>; |
| lantiq,pull = <0>; |
| }; |
| nand_cs1 { |
| lantiq,groups = "nand cs1"; |
| lantiq,function = "ebu"; |
| lantiq,open-drain = <0>; |
| lantiq,pull = <0>; |
| }; |
| |
| pci_in { |
| lantiq,groups = "req1"; |
| lantiq,function = "pci"; |
| lantiq,output = <0>; |
| lantiq,open-drain = <1>; |
| lantiq,pull = <2>; |
| }; |
| pci_out { |
| lantiq,groups = "gnt1"; |
| lantiq,function = "pci"; |
| lantiq,output = <1>; |
| lantiq,open-drain = <0>; |
| lantiq,pull = <0>; |
| }; |
| |
| pci_rst { |
| lantiq,pins = "io21"; |
| lantiq,output = <1>; |
| lantiq,open-drain = <0>; |
| }; |
| }; |
| }; |
| |
| etop@E180000 { |
| phy-mode = "rgmii"; |
| }; |
| |
| ifxhcd@E101000 { |
| status = "okay"; |
| gpios = <&gpio 33 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| gpio-keys-polled { |
| compatible = "gpio-keys-polled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| poll-interval = <100>; |
| reset { |
| label = "reset"; |
| gpios = <&gpio 54 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RESTART>; |
| }; |
| restart { |
| label = "restart"; |
| gpios = <&gpio 52 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_POWER>; |
| }; |
| wps { |
| label = "wps"; |
| gpios = <&gpio 53 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_WPS_BUTTON>; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| |
| wireless-red { |
| label = "bthomehubv3a:red:wireless"; |
| gpios = <&gpio 2 GPIO_ACTIVE_LOW>; |
| }; |
| wireless-orange { |
| label = "bthomehubv3a:orange:wireless"; |
| gpios = <&gpio 6 GPIO_ACTIVE_LOW>; |
| }; |
| wireless_blue: wireless-blue { |
| label = "bthomehubv3a:blue:wireless"; |
| gpios = <&gpio 9 GPIO_ACTIVE_LOW>; |
| }; |
| |
| broadband-red { |
| label = "bthomehubv3a:red:broadband"; |
| gpios = <&gpio 11 GPIO_ACTIVE_LOW>; |
| }; |
| broadband-orange { |
| label = "bthomehubv3a:orange:broadband"; |
| gpios = <&gpio 0 GPIO_ACTIVE_LOW>; |
| }; |
| broadband_blue: broadband-blue { |
| label = "bthomehubv3a:blue:broadband"; |
| gpios = <&gpio 12 GPIO_ACTIVE_LOW>; |
| }; |
| |
| power_red: power-red { |
| label = "bthomehubv3a:red:power"; |
| gpios = <&gpio 14 GPIO_ACTIVE_LOW>; |
| }; |
| power_orange: power-orange { |
| label = "bthomehubv3a:orange:power"; |
| gpios = <&gpio 5 GPIO_ACTIVE_LOW>; |
| default-state = "keep"; |
| }; |
| power_blue: power-blue { |
| label = "bthomehubv3a:blue:power"; |
| gpios = <&gpio 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| }; |
| |
| &pci0 { |
| status = "okay"; |
| gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; |
| |
| ath9k@7000 { |
| reg = <0x7000 0 0 0 0>; |
| qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ |
| }; |
| }; |
