| /branches/gl-inet/target/linux/lantiq/files-4.9/arch/mips/boot/dts/ARV7519PW.dts |
|---|
| @@ -0,0 +1,229 @@ |
|---|
| /dts-v1/; |
| |
| #include "danube.dtsi" |
| |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| compatible = "arcadyan,arv7519pw", "lantiq,xway", "lantiq,danube"; |
| model = "Astoria Networks ARV7519PW"; |
| |
| chosen { |
| bootargs = "console=ttyLTQ0,115200"; |
| }; |
| |
| aliases { |
| led-boot = &power; |
| led-failsafe = &power2; |
| led-running = &power; |
| |
| led-dsl = &dsl; |
| led-internet = &online; |
| led-wifi = &wifi; |
| }; |
| |
| memory@0 { |
| reg = <0x0 0x4000000>; |
| }; |
| |
| sram@1F000000 { |
| vmmc@107000 { |
| status = "okay"; |
| }; |
| }; |
| |
| fpi@10000000 { |
| localbus@0 { |
| nor-boot@0 { |
| compatible = "lantiq,nor"; |
| bank-width = <2>; |
| reg = <0 0x0 0x2000000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "uboot"; |
| reg = <0x00000 0x40000>; |
| read-only; |
| }; |
| |
| partition@40000 { |
| label = "uboot_env"; |
| reg = <0x40000 0x20000>; |
| }; |
| |
| partition@60000 { |
| label = "firmware"; |
| reg = <0x60000 0xf80000>; |
| }; |
| |
| boardconfig: partition@fe0000 { |
| label = "board_config"; |
| reg = <0xfe0000 0x20000>; |
| read-only; |
| }; |
| }; |
| }; |
| }; |
| |
| gpio: pinmux@E100B10 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&state_default>; |
| |
| state_default: pinmux { |
| ebu { |
| lantiq,groups = "ebu cs1"; |
| lantiq,function = "ebu"; |
| }; |
| pci_in { |
| lantiq,groups = "req1"; |
| lantiq,function = "pci"; |
| lantiq,open-drain = <1>; |
| lantiq,pull = <2>; |
| lantiq,output = <0>; |
| }; |
| pci_out { |
| lantiq,groups = "gnt1"; |
| lantiq,function = "pci"; |
| lantiq,pull = <0>; |
| lantiq,output = <1>; |
| }; |
| pci_rst { |
| lantiq,pins = "io21"; |
| lantiq,pull = <2>; |
| lantiq,output = <1>; |
| }; |
| switch_rst { |
| lantiq,pins = "io19"; |
| lantiq,pull = <2>; |
| lantiq,output = <1>; |
| }; |
| }; |
| }; |
| |
| etop@E180000 { |
| phy-mode = "mii"; |
| mtd-mac-address = <&boardconfig 0x16>; |
| }; |
| |
| /* warning: passive port |
| only works with active devices */ |
| ifxhcd@E101000 { |
| status = "okay"; |
| }; |
| }; |
| |
| gpio-keys-polled { |
| compatible = "gpio-keys-polled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| poll-interval = <100>; |
| |
| rfkill { |
| label = "rfkill"; |
| gpios = <&gpio 11 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RFKILL>; |
| }; |
| reset { |
| label = "reset"; |
| gpios = <&gpio 28 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RESTART>; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| power: power { |
| label = "power"; |
| gpios = <&gpio 2 GPIO_ACTIVE_LOW>; |
| default-state = "keep"; |
| }; |
| power2: power2 { |
| label = "power2"; |
| gpios = <&gpio 14 GPIO_ACTIVE_LOW>; |
| }; |
| online: online { |
| label = "online"; |
| gpios = <&gpio 3 GPIO_ACTIVE_LOW>; |
| }; |
| online2 { |
| label = "online2"; |
| gpios = <&gpio 30 GPIO_ACTIVE_LOW>; |
| }; |
| wifi: wifi { |
| label = "wifi"; |
| gpios = <&gpio 12 GPIO_ACTIVE_LOW>; |
| }; |
| wifi2 { |
| label = "wifi2"; |
| gpios = <&gpio 10 GPIO_ACTIVE_LOW>; |
| }; |
| wifi3 { |
| label = "wifi3"; |
| gpios = <&gpio 6 GPIO_ACTIVE_LOW>; |
| }; |
| voice { |
| label = "voice"; |
| gpios = <&gpio 31 GPIO_ACTIVE_LOW>; |
| }; |
| wps { |
| label = "wps"; |
| gpios = <&gpio 15 GPIO_ACTIVE_LOW>; |
| }; |
| wps2 { |
| label = "wps2"; |
| gpios = <&gpio 7 GPIO_ACTIVE_LOW>; |
| }; |
| wps3 { |
| label = "wps3"; |
| gpios = <&gpio 23 GPIO_ACTIVE_LOW>; |
| }; |
| dsl: dsl { |
| label = "dsl"; |
| gpios = <&gpio 4 GPIO_ACTIVE_LOW>; |
| }; |
| lan { |
| label = "lan"; |
| gpios = <&gpio 1 GPIO_ACTIVE_LOW>; |
| }; |
| tv { |
| label = "tv"; |
| gpios = <&gpio 20 GPIO_ACTIVE_LOW>; |
| }; |
| upgrade { |
| label = "upgrade"; |
| gpios = <&gpio 29 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| /* is there another way to "reserve" the GPIO? */ |
| gpio_export { |
| compatible = "gpio-export"; |
| #size-cells = <0>; |
| |
| switch { |
| gpio-export,name = "switch"; |
| gpio-export,output = <1>; |
| gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| }; |
| |
| &pci0 { |
| status = "okay"; |
| lantiq,external-clock; |
| gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; |
| req-mask = <0xf>; |
| |
| wifi@0,0 { |
| compatible = "pci0,0"; |
| reg = <0x7000 0 0 0 0>; |
| ralink,mtd-eeprom = <&boardconfig 0x410>; |
| ralink,mtd-eeprom-swap; |
| }; |
| }; |
