| /branches/gl-inet/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-d7800.dts |
|---|
| @@ -0,0 +1,410 @@ |
|---|
| #include "qcom-ipq8064-v2.0.dtsi" |
| |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| model = "Netgear Nighthawk X4 D7800"; |
| compatible = "netgear,d7800", "qcom,ipq8064"; |
| |
| memory@0 { |
| reg = <0x42000000 0xe000000>; |
| device_type = "memory"; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| rsvd@41200000 { |
| reg = <0x41200000 0x300000>; |
| no-map; |
| }; |
| }; |
| |
| aliases { |
| serial0 = &gsbi4_serial; |
| mdio-gpio0 = &mdio0; |
| |
| led-boot = &power_white; |
| led-failsafe = &power_amber; |
| led-running = &power_white; |
| led-upgrade = &power_amber; |
| }; |
| |
| chosen { |
| bootargs = "rootfstype=squashfs noinitrd"; |
| linux,stdout-path = "serial0:115200n8"; |
| }; |
| |
| soc { |
| pinmux@800000 { |
| button_pins: button_pins { |
| mux { |
| pins = "gpio6", "gpio54", "gpio65"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| i2c4_pins: i2c4_pinmux { |
| mux { |
| pins = "gpio12", "gpio13"; |
| function = "gsbi4"; |
| drive-strength = <12>; |
| bias-disable; |
| }; |
| }; |
| |
| led_pins: led_pins { |
| mux { |
| pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23", |
| "gpio24","gpio26", "gpio53", "gpio64"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| mdio0_pins: mdio0_pins { |
| mux { |
| pins = "gpio0", "gpio1"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| }; |
| |
| nand_pins: nand_pins { |
| mux { |
| pins = "gpio34", "gpio35", "gpio36", |
| "gpio37", "gpio38", "gpio39", |
| "gpio40", "gpio41", "gpio42", |
| "gpio43", "gpio44", "gpio45", |
| "gpio46", "gpio47"; |
| function = "nand"; |
| drive-strength = <10>; |
| bias-disable; |
| }; |
| pullups { |
| pins = "gpio39"; |
| bias-pull-up; |
| }; |
| hold { |
| pins = "gpio40", "gpio41", "gpio42", |
| "gpio43", "gpio44", "gpio45", |
| "gpio46", "gpio47"; |
| bias-bus-hold; |
| }; |
| }; |
| |
| rgmii2_pins: rgmii2_pins { |
| mux { |
| pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", |
| "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; |
| function = "rgmii2"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| }; |
| |
| usb0_pwr_en_pins: usb0_pwr_en_pins { |
| mux { |
| pins = "gpio15"; |
| function = "gpio"; |
| drive-strength = <12>; |
| bias-pull-down; |
| output-high; |
| }; |
| }; |
| |
| usb1_pwr_en_pins: usb1_pwr_en_pins { |
| mux { |
| pins = "gpio16", "gpio68"; |
| function = "gpio"; |
| drive-strength = <12>; |
| bias-pull-down; |
| output-high; |
| }; |
| }; |
| }; |
| |
| gsbi@16300000 { |
| qcom,mode = <GSBI_PROT_I2C_UART>; |
| status = "ok"; |
| serial@16340000 { |
| status = "ok"; |
| }; |
| /* |
| * The i2c device on gsbi4 should not be enabled. |
| * On ipq806x designs gsbi4 i2c is meant for exclusive |
| * RPM usage. Turning this on in kernel manifests as |
| * i2c failure for the RPM. |
| */ |
| }; |
| |
| sata-phy@1b400000 { |
| status = "ok"; |
| }; |
| |
| sata@29000000 { |
| ports-implemented = <0x1>; |
| status = "ok"; |
| }; |
| |
| phy@100f8800 { /* USB3 port 1 HS phy */ |
| status = "ok"; |
| }; |
| |
| phy@100f8830 { /* USB3 port 1 SS phy */ |
| status = "ok"; |
| }; |
| |
| phy@110f8800 { /* USB3 port 0 HS phy */ |
| status = "ok"; |
| }; |
| |
| phy@110f8830 { /* USB3 port 0 SS phy */ |
| status = "ok"; |
| }; |
| |
| usb30@0 { |
| status = "ok"; |
| |
| pinctrl-0 = <&usb0_pwr_en_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| usb30@1 { |
| status = "ok"; |
| |
| pinctrl-0 = <&usb1_pwr_en_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| pcie0: pci@1b500000 { |
| status = "ok"; |
| reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&pcie0_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| pcie1: pci@1b700000 { |
| status = "ok"; |
| reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&pcie1_pins>; |
| pinctrl-names = "default"; |
| force_gen1 = <1>; |
| }; |
| |
| nand@1ac00000 { |
| status = "ok"; |
| |
| pinctrl-0 = <&nand_pins>; |
| pinctrl-names = "default"; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| cs0 { |
| reg = <0>; |
| compatible = "qcom,nandcs"; |
| |
| nand-ecc-strength = <4>; |
| nand-bus-width = <8>; |
| nand-ecc-step-size = <512>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| qcadata@0 { |
| label = "qcadata"; |
| reg = <0x0000000 0x0c80000>; |
| read-only; |
| }; |
| |
| APPSBL@c80000 { |
| label = "APPSBL"; |
| reg = <0x0c80000 0x0500000>; |
| read-only; |
| }; |
| |
| APPSBLENV@1180000 { |
| label = "APPSBLENV"; |
| reg = <0x1180000 0x0080000>; |
| read-only; |
| }; |
| |
| art: art@1200000 { |
| label = "art"; |
| reg = <0x1200000 0x0140000>; |
| read-only; |
| }; |
| |
| artbak: art@1340000 { |
| label = "artbak"; |
| reg = <0x1340000 0x0140000>; |
| read-only; |
| }; |
| |
| kernel@1480000 { |
| label = "kernel"; |
| reg = <0x1480000 0x0400000>; |
| }; |
| |
| ubi@1880000 { |
| label = "ubi"; |
| reg = <0x1880000 0x1C00000>; |
| }; |
| |
| netgear@3480000 { |
| label = "netgear"; |
| reg = <0x3480000 0x4480000>; |
| read-only; |
| }; |
| |
| reserve@7900000 { |
| label = "reserve"; |
| reg = <0x7900000 0x0700000>; |
| read-only; |
| }; |
| }; |
| }; |
| }; |
| |
| mdio0: mdio { |
| compatible = "virtual,mdio-gpio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&mdio0_pins>; |
| pinctrl-names = "default"; |
| |
| phy0: ethernet-phy@0 { |
| device_type = "ethernet-phy"; |
| reg = <0>; |
| qca,ar8327-initvals = < |
| 0x00004 0x7600000 /* PAD0_MODE */ |
| 0x00008 0x1000000 /* PAD5_MODE */ |
| 0x0000c 0x80 /* PAD6_MODE */ |
| 0x000e4 0x6a545 /* MAC_POWER_SEL */ |
| 0x000e0 0xc74164de /* SGMII_CTRL */ |
| 0x0007c 0x4e /* PORT0_STATUS */ |
| 0x00094 0x4e /* PORT6_STATUS */ |
| >; |
| }; |
| |
| phy4: ethernet-phy@4 { |
| device_type = "ethernet-phy"; |
| reg = <4>; |
| }; |
| }; |
| |
| gmac1: ethernet@37200000 { |
| status = "ok"; |
| phy-mode = "rgmii"; |
| phy-handle = <&phy4>; |
| qcom,id = <1>; |
| |
| pinctrl-0 = <&rgmii2_pins>; |
| pinctrl-names = "default"; |
| |
| mtd-mac-address = <&art 6>; |
| }; |
| |
| gmac2: ethernet@37400000 { |
| status = "ok"; |
| phy-mode = "sgmii"; |
| qcom,id = <2>; |
| |
| mtd-mac-address = <&art 0>; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| pinctrl-0 = <&button_pins>; |
| pinctrl-names = "default"; |
| |
| wifi { |
| label = "wifi"; |
| gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RFKILL>; |
| }; |
| |
| reset { |
| label = "reset"; |
| gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RESTART>; |
| }; |
| |
| wps { |
| label = "wps"; |
| gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_WPS_BUTTON>; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| pinctrl-0 = <&led_pins>; |
| pinctrl-names = "default"; |
| |
| usb1 { |
| label = "d7800:white:usb1"; |
| gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| usb2 { |
| label = "d7800:white:usb2"; |
| gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| power_amber: power_amber { |
| label = "d7800:amber:power"; |
| gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| wan_white { |
| label = "d7800:white:wan"; |
| gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| wan_amber { |
| label = "d7800:amber:wan"; |
| gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| wps { |
| label = "d7800:white:wps"; |
| gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| esata { |
| label = "d7800:white:esata"; |
| gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| power_white: power_white { |
| label = "d7800:white:power"; |
| gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; |
| default-state = "keep"; |
| }; |
| |
| wifi { |
| label = "d7800:white:wifi"; |
| gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| }; |
| |
| &adm_dma { |
| status = "ok"; |
| }; |
