/branches/gl-inet/package/network/config/ltq-vdsl-app/files/dsl_control |
@@ -0,0 +1,314 @@ |
#!/bin/sh /etc/rc.common |
# Copyright (C) 2012 OpenWrt.org |
|
START=97 |
USE_PROCD=1 |
|
EXTRA_COMMANDS="status lucistat" |
EXTRA_HELP=" status Get DSL status information |
lucistat Get status information if lua friendly format" |
|
[ -f /lib/functions/lantiq_dsl.sh ] && . /lib/functions/lantiq_dsl.sh |
|
# |
# ITU-T G.997.1 (06/2012) - Section 7.3.1.1.1 (xTU transmission system enabling (XTSE)) |
# ITU-T G.997.1 Amendment 2 (04/2013) - Section 2.1 - (Vectoring mode enable (VECTORMODE_ENABLE)) |
# |
# G.992.1 Annex A |
# G.992.2 Annex A |
# G.992.3 Annex A / L-US1 / L_US-2 / M |
# G.992.5 Annex A / M |
# G.993.2 Annex A/B/C |
# G.993.5 Annex A/B/C |
xtse_xdsl_a="05_01_04_00_4C_01_04_07" |
|
# G.992.1 Annex B |
# G.992.3 Annex B |
# G.992.5 Annex B |
# G.993.2 Annex A/B/C |
# G.993.5 Annex A/B/C |
xtse_xdsl_b="10_00_10_00_00_04_00_07" |
|
# G.992.1 Annex B |
# G.992.3 Annex B |
# G.992.3 Annex J |
# G.992.5 Annex B |
# G.992.5 Annex J |
# G.993.2 Annex A/B/C |
# G.993.5 Annex A/B/C |
xtse_xdsl_j="10_00_10_40_00_04_01_07" |
|
# G.992.1 Annex B |
xtse_xdsl_bdmt="10_00_00_00_00_00_00_00" |
|
# G.992.3 Annex B |
xtse_xdsl_b2="00_00_10_00_00_00_00_00" |
|
# G.992.5 Annex B |
xtse_xdsl_b2p="00_00_00_00_00_04_00_00" |
|
# ANSI T1.413 |
xtse_xdsl_at1="01_00_00_00_00_00_00_00" |
|
# G.992.2 Annex A |
xtse_xdsl_alite="00_01_00_00_00_00_00_00" |
|
# G.992.1 Annex A |
xtse_xdsl_admt="04_00_00_00_00_00_00_00" |
|
# G.992.3 Annex A |
xtse_xdsl_a2="00_00_04_00_00_00_00_00" |
|
# G.992.5 Annex A |
xtse_xdsl_a2p="00_00_00_00_00_01_00_00" |
|
# G.992.3 Annex L |
xtse_xdsl_l="00_00_00_00_0C_00_00_00" |
|
# G.992.3 Annex M |
# G.992.5 Annex M |
xtse_xdsl_m="00_00_00_00_40_00_04_00" |
|
# G.992.3 Annex M |
xtse_xdsl_m2="00_00_00_00_40_00_00_00" |
|
# G.992.5 Annex M |
xtse_xdsl_m2p="00_00_00_00_00_00_04_00" |
|
# |
# ITU-T G.994.1 (06/2012) - Table 2 (Mandatory carrier sets) |
# |
|
# A43 |
tone_adsl_a="0x142" # A43C + J43 + A43 |
tone_vdsl_a="0x142" # A43C + J43 + A43 |
|
# A43 + V43 |
tone_adsl_av="0x142" # A43C + J43 + A43 |
tone_vdsl_av="0x146" # A43C + J43 + A43 + V43 |
|
# B43 |
tone_adsl_b="0x81" # B43 + B43c |
tone_vdsl_b="0x1" # B43 |
|
# B43 + V43 |
tone_adsl_bv="0x81" # B43 + B43c |
tone_vdsl_bv="0x5" # B43 + V43 |
|
# create ADSL autoboot script. Used for SNR margin tweak |
autoboot_script() { |
echo "[WaitForConfiguration]={ |
locs 0 $1 |
} |
|
[WaitForLinkActivate]={ |
} |
|
[WaitForRestart]={ |
} |
|
[Common]={ |
}" > /tmp/dsl.scr |
} |
|
lowlevel_cfg() { |
echo "# VRX Low Level Configuration File |
# |
# Parameters must be separated by tabs or spaces. |
# Empty lines and comments will be ignored. |
# |
|
# nFilter |
# |
# NA = -1 |
# OFF = 0 |
# ISDN = 1 |
# POTS = 2 |
# POTS_2 = 3 |
# POTS_3 = 4 |
# |
# (dec) |
-1 |
|
# nHsToneGroupMode nHsToneGroup_A nHsToneGroup_V nHsToneGroup_AV |
# |
# NA = -1 NA = -1 see see |
# AUTO = 0 VDSL2_B43 = 0x0001 nHsToneGroup_A nHsToneGroup_A |
# MANUAL = 1 VDSL2_A43 = 0x0002 |
# VDSL2_V43 = 0x0004 |
# VDSL1_V43P = 0x0008 |
# VDSL1_V43I = 0x0010 |
# ADSL1_C43 = 0x0020 |
# ADSL2_J43 = 0x0040 |
# ADSL2_B43C = 0x0080 |
# ADSL2_A43C = 0x0100 |
# |
# (dec) (hex) (hex) (hex) |
1 $1 $2 0x0 |
|
# nBaseAddr nIrqNum |
# |
# (hex) (dec) |
0x1e116000 63 |
|
# nUtopiaPhyAdr nUtopiaBusWidth nPosPhyParity |
# default(16b) = 0 NA = -1 |
# 8-bit = 1 ODD = 0 |
# 16-bit = 2 |
# |
# |
# (hex) (dec) (dec) |
0xFF 0 0 |
|
# bNtrEnable |
# |
# (dec) |
0" > /tmp/lowlevel.cfg |
} |
|
service_triggers() { |
procd_add_reload_trigger network |
} |
|
start_service() { |
local annex |
local firmware |
local tone |
local tone_adsl |
local tone_vdsl |
local xtse |
local xfer_mode |
local line_mode |
local tc_layer |
local mode |
local lowlevel |
local snr |
|
config_load network |
config_get tone dsl tone |
config_get annex dsl annex |
config_get firmware dsl firmware |
config_get xfer_mode dsl xfer_mode |
config_get line_mode dsl line_mode |
config_get snr dsl ds_snr_offset |
|
eval "xtse=\"\${xtse_xdsl_$annex}\"" |
|
case "${xfer_mode}" in |
atm) |
tc_layer="-T1:0x1:0x1_1:0x1:0x1" |
;; |
ptm) |
tc_layer="-T2:0x1:0x1_2:0x1:0x1" |
;; |
esac |
|
case "${line_mode}" in |
adsl) |
mode="-M1" |
|
# mask out VDSL bits when ADSL is requested |
xtse="${xtse%_*}_00" |
;; |
vdsl) |
mode="-M2" |
|
# mask out ADSL bits when VDSL is requested |
xtse="00_00_00_00_00_00_00_${xtse##*_}" |
;; |
esac |
|
local annexgpio="/sys/class/gpio/annex" |
if [ -d "${annexgpio}a" ] && [ -d "${annexgpio}b" ]; then |
case "${annex}" in |
a*|l*|m*) |
echo 1 > "${annexgpio}a/value" |
echo 0 > "${annexgpio}b/value" |
;; |
b*|j*) |
echo 0 > "${annexgpio}a/value" |
echo 1 > "${annexgpio}b/value" |
;; |
esac |
fi |
|
if [ -z "${firmware}" ]; then |
# search for the firmware provided by dsl-vrx200-firmware-xdsl-* |
if grep -qE "system type.*: (VR9|xRX200)" /proc/cpuinfo; then |
case "${annex}" in |
a*|l*|m*) |
if [ -f "/lib/firmware/lantiq-vrx200-a.bin" ]; then |
firmware="/lib/firmware/lantiq-vrx200-a.bin" |
elif [ -f "/tmp/lantiq-vrx200-a.bin" ]; then |
firmware="/tmp/lantiq-vrx200-a.bin" |
elif [ -f "/lib/firmware/lantiq-vrx200-b.bin" ] && [ -f "/lib/firmware/lantiq-vrx200-b-to-a.bspatch" ]; then |
bspatch /lib/firmware/lantiq-vrx200-b.bin \ |
/tmp/lantiq-vrx200-a.bin \ |
/lib/firmware/lantiq-vrx200-b-to-a.bspatch |
firmware="/tmp/lantiq-vrx200-a.bin" |
else |
echo "firmware for annex a not found" |
return 1 |
fi |
;; |
b*|j*) |
if [ -f "/lib/firmware/lantiq-vrx200-b.bin" ]; then |
firmware="/lib/firmware/lantiq-vrx200-b.bin" |
elif [ -f "/tmp/lantiq-vrx200-b.bin" ]; then |
firmware="/tmp/lantiq-vrx200-b.bin" |
elif [ -f "/lib/firmware/lantiq-vrx200-a.bin" ] && [ -f "/lib/firmware/lantiq-vrx200-a-to-b.bspatch" ]; then |
bspatch /lib/firmware/lantiq-vrx200-a.bin \ |
/tmp/lantiq-vrx200-b.bin \ |
/lib/firmware/lantiq-vrx200-a-to-b.bspatch |
firmware="/tmp/lantiq-vrx200-b.bin" |
else |
echo "firmware for annex b not found" |
return 1 |
fi |
;; |
*) |
echo "annex type not supported use a or b" |
return 1 |
;; |
esac |
fi |
fi |
|
[ -z "${firmware}" ] && firmware=/lib/firmware/vdsl.bin |
[ -f "${firmware}" ] || { |
echo failed to find $firmware |
return 1 |
} |
|
eval "tone_adsl=\"\${tone_adsl_$tone}\"" |
eval "tone_vdsl=\"\${tone_vdsl_$tone}\"" |
[ -n "${tone_adsl}" ] && [ -n "${tone_vdsl}" ] && { |
lowlevel_cfg "${tone_adsl}" "${tone_vdsl}" |
lowlevel="-l /tmp/lowlevel.cfg" |
} |
|
[ -z "${snr}" ] || { |
# for SNR offset setting |
autoboot_script "$snr" |
autoboot="-a /tmp/dsl.scr -A /tmp/dsl.scr" |
} |
|
procd_open_instance |
procd_set_param command /sbin/vdsl_cpe_control \ |
-i$xtse \ |
-n /sbin/dsl_notify.sh \ |
-f ${firmware} \ |
$lowlevel \ |
${mode} \ |
${tc_layer} \ |
$autoboot |
procd_close_instance |
} |
|
stop_service() { |
# do not use dsl_cmd to not block when this is locked up by some other proess |
echo quit > /tmp/pipe/dsl_cpe0_cmd |
DSL_NOTIFICATION_TYPE="DSL_INTERFACE_STATUS" \ |
DSL_INTERFACE_STATUS="DOWN" \ |
/sbin/dsl_notify.sh |
} |