/branches/18.06.1/target/linux/ramips/dts/ki_rb.dts |
@@ -0,0 +1,216 @@ |
/dts-v1/; |
|
#include "mt7628an.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
compatible = "zyxel,keenetic-extra-ii", "mediatek,mt7628an-soc"; |
model = "ZyXEL Keenetic Extra II"; |
|
aliases { |
led-boot = &led_power; |
led-failsafe = &led_power; |
led-running = &led_power; |
led-upgrade = &led_power; |
}; |
|
memory@0 { |
device_type = "memory"; |
reg = <0x0 0x8000000>; |
}; |
|
chosen { |
bootargs = "console=ttyS0,57600n8"; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <20>; |
|
reset { |
label = "reset"; |
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
|
wps { |
label = "wps"; |
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_WPS_BUTTON>; |
}; |
|
fn { |
label = "fn"; |
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; |
linux,code = <BTN_0>; |
}; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
led_power: power { |
label = "keenetic-extra-ii:green:power"; |
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
default-state = "keep"; |
}; |
|
internet { |
label = "keenetic-extra-ii:green:internet"; |
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; |
}; |
|
wifi { |
label = "keenetic-extra-ii:green:wifi"; |
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; |
}; |
|
usb { |
label = "keenetic-extra-ii:green:usb"; |
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
trigger-sources = <&ohci_port1>, <&ehci_port1>; |
linux,default-trigger = "usbport"; |
}; |
}; |
|
gpio_export { |
compatible = "gpio-export"; |
#size-cells = <0>; |
|
usbpower { |
gpio-export,name = "usbpower"; |
gpio-export,output = <1>; |
gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; |
}; |
}; |
}; |
|
&spi0 { |
status = "okay"; |
|
m25p80@0 { |
compatible = "jedec,spi-nor"; |
reg = <0>; |
spi-max-frequency = <10000000>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
partition@0 { |
label = "u-boot"; |
reg = <0x0 0x30000>; |
read-only; |
}; |
|
partition@30000 { |
label = "u-config"; |
reg = <0x30000 0x10000>; |
read-only; |
}; |
|
factory: partition@40000 { |
label = "rf-eeprom"; |
reg = <0x40000 0x10000>; |
read-only; |
}; |
|
partition@50000 { |
compatible = "denx,uimage"; |
label = "firmware"; |
reg = <0x50000 0xe90000>; |
}; |
|
partition@ee0000 { |
label = "config_1"; |
reg = <0xee0000 0x10000>; |
read-only; |
}; |
|
partition@ef0000 { |
label = "storage"; |
reg = <0xef0000 0x100000>; |
read-only; |
}; |
|
partition@ff0000 { |
label = "dump"; |
reg = <0xff0000 0x10000>; |
read-only; |
}; |
|
partition@1000000 { |
label = "u-state"; |
reg = <0x1000000 0x30000>; |
read-only; |
}; |
|
partition@1030000 { |
label = "u-config_res"; |
reg = <0x1030000 0x10000>; |
read-only; |
}; |
|
partition@1040000 { |
label = "rf-eeprom_res"; |
reg = <0x1040000 0x10000>; |
read-only; |
}; |
|
partition@1050000 { |
label = "firmware_2"; |
reg = <0x1050000 0xe90000>; |
read-only; |
}; |
|
partition@1ee0000 { |
label = "config_2"; |
reg = <0x1ee0000 0x10000>; |
read-only; |
}; |
}; |
}; |
}; |
|
&ehci { |
status = "okay"; |
}; |
|
&ohci { |
status = "okay"; |
}; |
|
ðernet { |
mtd-mac-address = <&factory 0x4>; |
mediatek,portmap = "wllll"; |
}; |
|
&wmac { |
status = "okay"; |
mediatek,mtd-eeprom = <&factory 0x0>; |
}; |
|
&pcie { |
status = "okay"; |
}; |
|
&pcie0 { |
mt76@0,0 { |
reg = <0x0000 0 0 0 0>; |
mediatek,mtd-eeprom = <&factory 0x8000>; |
ieee80211-freq-limit = <5000000 6000000>; |
mtd-mac-address = <&factory 0x8004>; |
}; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "gpio", "i2s", "refclk", "spi cs1", "uart1", "wled_an"; |
ralink,function = "gpio"; |
}; |
}; |
}; |