/branches/18.06.1/target/linux/ramips/dts/ZBT-CPE102.dts |
@@ -0,0 +1,129 @@ |
/dts-v1/; |
|
#include "mt7620n.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
compatible = "zbtlink,zbt-cpe102", "ralink,mt7620n-soc"; |
model = "Zbtlink ZBT-CPE102"; |
|
chosen { |
bootargs = "console=ttyS0,115200"; |
}; |
|
|
aliases { |
led-boot = &led_4g_0; |
led-failsafe = &led_4g_0; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
led_4g_0: 4g-0 { |
label = "zbt-cpe102:green:4g-0"; |
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
}; |
|
4g-1 { |
label = "zbt-cpe102:green:4g-1"; |
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
}; |
|
4g-2 { |
label = "zbt-cpe102:green:4g-2"; |
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; |
}; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <20>; |
|
reset { |
label = "reset"; |
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
}; |
}; |
|
&gpio1 { |
status = "okay"; |
}; |
|
&gpio2 { |
status = "okay"; |
}; |
|
&gpio3 { |
status = "okay"; |
}; |
|
&spi0 { |
status = "okay"; |
|
en25q64@0 { |
compatible = "jedec,spi-nor"; |
reg = <0>; |
spi-max-frequency = <10000000>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
partition@0 { |
label = "u-boot"; |
reg = <0x0 0x30000>; |
read-only; |
}; |
|
partition@30000 { |
label = "u-boot-env"; |
reg = <0x30000 0x10000>; |
read-only; |
}; |
|
factory: partition@40000 { |
label = "factory"; |
reg = <0x40000 0x10000>; |
read-only; |
}; |
|
partition@50000 { |
compatible = "denx,uimage"; |
label = "firmware"; |
reg = <0x50000 0x760000>; |
}; |
}; |
}; |
}; |
|
&ehci { |
status = "okay"; |
}; |
|
&ohci { |
status = "okay"; |
}; |
|
ðernet { |
mtd-mac-address = <&factory 0x4>; |
mediatek,portmap = "wllll"; |
}; |
|
&wmac { |
ralink,mtd-eeprom = <&factory 0>; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
default { |
ralink,group = "i2c", "spi refclk", "wled"; |
ralink,function = "gpio"; |
}; |
}; |
}; |