| /branches/18.06.1/target/linux/ramips/dts/ZBT-APE522II.dts |
|---|
| @@ -0,0 +1,144 @@ |
|---|
| /dts-v1/; |
| |
| #include "mt7620a.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| compatible = "zbtlink,zbt-ape522ii", "ralink,mt7620a-soc"; |
| model = "ZBT-APE522II"; |
| |
| chosen { |
| bootargs = "console=ttyS0,115200"; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| sys1 { |
| label = "zbt-ape522ii:green:sys1"; |
| gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sys2 { |
| label = "zbt-ape522ii:green:sys2"; |
| gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sys3 { |
| label = "zbt-ape522ii:green:sys3"; |
| gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sys4 { |
| label = "zbt-ape522ii:green:sys4"; |
| gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
| }; |
| |
| wlan2g4 { |
| label = "zbt-ape522ii:green:wlan2g4"; |
| gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| keys { |
| compatible = "gpio-keys-polled"; |
| poll-interval = <20>; |
| |
| reset { |
| label = "reset"; |
| gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; |
| linux,code = <KEY_RESTART>; |
| }; |
| }; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &gpio2 { |
| status = "okay"; |
| }; |
| |
| &gpio3 { |
| status = "okay"; |
| }; |
| |
| &spi0 { |
| status = "okay"; |
| |
| m25p80@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <10000000>; |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| partition@0 { |
| label = "u-boot"; |
| reg = <0x0 0x30000>; |
| }; |
| |
| partition@30000 { |
| label = "u-boot-env"; |
| reg = <0x30000 0x10000>; |
| read-only; |
| }; |
| |
| factory: partition@40000 { |
| label = "factory"; |
| reg = <0x40000 0x10000>; |
| read-only; |
| }; |
| |
| partition@50000 { |
| compatible = "denx,uimage"; |
| label = "firmware"; |
| reg = <0x50000 0xf80000>; |
| }; |
| }; |
| }; |
| }; |
| |
| ðernet { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ephy_pins>; |
| mtd-mac-address = <&factory 0x4>; |
| mediatek,portmap = "wllll"; |
| }; |
| |
| &wmac { |
| ralink,mtd-eeprom = <&factory 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pa_pins>; |
| }; |
| |
| &pcie { |
| status = "okay"; |
| }; |
| |
| &pcie0 { |
| mt76@0,0 { |
| reg = <0x0000 0 0 0 0>; |
| mediatek,mtd-eeprom = <&factory 0x8000>; |
| ieee80211-freq-limit = <5000000 6000000>; |
| }; |
| }; |
| |
| &pinctrl { |
| state_default: pinctrl0 { |
| gpio { |
| ralink,group = "wled", "i2c", "uartf", "wdt"; |
| ralink,function = "gpio"; |
| }; |
| }; |
| }; |
