/branches/18.06.1/target/linux/ramips/dts/WLI-TX4-AG300N.dts |
@@ -0,0 +1,125 @@ |
/dts-v1/; |
|
#include "rt2880.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
#address-cells = <1>; |
#size-cells = <1>; |
compatible = "buffalo,wli-tx4-ag300n", "ralink,rt2880-soc"; |
model = "Buffalo WLI-TX4-AG300N"; |
|
aliases { |
led-boot = &led_power; |
led-failsafe = &led_power; |
led-running = &led_power; |
led-upgrade = &led_power; |
}; |
|
cfi@1f000000 { |
compatible = "cfi-flash"; |
reg = <0x1f000000 0x800000>; |
bank-width = <2>; |
device-width = <2>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
partition@0 { |
label = "uboot"; |
reg = <0x0 0x30000>; |
read-only; |
}; |
|
partition@30000 { |
label = "uboot-env"; |
reg = <0x30000 0x10000>; |
read-only; |
}; |
|
factory: partition@40000 { |
label = "factory"; |
reg = <0x40000 0x10000>; |
read-only; |
}; |
|
partition@50000 { |
compatible = "denx,uimage"; |
label = "firmware"; |
reg = <0x50000 0x3b0000>; |
}; |
}; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <100>; |
|
wps { |
label = "wps"; |
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_WPS_BUTTON>; |
}; |
|
bandwidth { |
label = "bandwidth"; |
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; |
linux,code = <KEY_RESTART>; |
}; |
|
reset { |
label = "reset"; |
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
diag { |
label = "wli-tx4-ag300n:red:diag"; |
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
}; |
|
led_power: power { |
label = "wli-tx4-ag300n:blue:power"; |
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
}; |
|
security { |
label = "wli-tx4-ag300n:blue:security"; |
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
}; |
}; |
}; |
|
&gpio0 { |
status = "okay"; |
}; |
|
ðernet { |
status = "okay"; |
mtd-mac-address = <&factory 0x4>; |
|
port@0 { |
mediatek,fixed-link = <100 1 1 1>; |
}; |
|
mdio-bus { |
status = "okay"; |
|
phy0: ethernet-phy@0 { |
phy-mode = "mii"; |
reg = <0>; |
}; |
}; |
}; |
|
&wmac { |
ralink,mtd-eeprom = <&factory 0>; |
}; |