/branches/18.06.1/target/linux/ramips/dts/WHR-1166D.dts/WHR-1166D.dts |
@@ -0,0 +1,182 @@ |
/dts-v1/; |
|
#include "mt7620a.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
compatible = "buffalo,whr-1166d", "ralink,mt7620a-soc"; |
model = "Buffalo WHR-1166D"; |
|
aliases { |
led-boot = &led_power_green; |
led-failsafe = &led_power_green; |
led-running = &led_power_green; |
led-upgrade = &led_power_green; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
power { |
label = "whr-1166d:red:power"; |
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
}; |
|
wifi { |
label = "whr-1166d:green:wifi"; |
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
}; |
|
led_power_green: power2 { |
label = "whr-1166d:green:power"; |
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; |
}; |
|
wifi2 { |
label = "whr-1166d:orange:wifi"; |
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; |
}; |
|
internet { |
label = "whr-1166d:green:internet"; |
gpios = <&gpio2 17 GPIO_ACTIVE_LOW>; |
}; |
|
router { |
label = "whr-1166d:orange:router"; |
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; |
}; |
|
router2 { |
label = "whr-1166d:green:router"; |
gpios = <&gpio2 19 GPIO_ACTIVE_LOW>; |
}; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <20>; |
|
reset { |
label = "reset"; |
gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
|
aoss { |
label = "aoss"; |
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_WPS_BUTTON>; |
}; |
|
ap { |
label = "ap"; |
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; |
linux,code = <BTN_0>; |
linux,input-type = <EV_SW>; |
}; |
|
bridge { |
label = "bridge"; |
gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; |
linux,code = <BTN_0>; |
linux,input-type = <EV_SW>; |
}; |
}; |
}; |
|
&gpio2 { |
status = "okay"; |
}; |
|
&spi0 { |
status = "okay"; |
|
m25p80@0 { |
compatible = "jedec,spi-nor"; |
reg = <0>; |
spi-max-frequency = <10000000>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
partition@0 { |
label = "u-boot"; |
reg = <0x0 0x30000>; |
read-only; |
}; |
|
partition@30000 { |
label = "u-boot-env"; |
reg = <0x30000 0x10000>; |
read-only; |
}; |
|
factory: partition@40000 { |
label = "factory"; |
reg = <0x40000 0x10000>; |
read-only; |
}; |
|
partition@50000 { |
compatible = "denx,uimage"; |
label = "firmware"; |
reg = <0x50000 0xfb0000>; |
}; |
}; |
}; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "i2c", "uartf", "wled", "nd_sd"; |
ralink,function = "gpio"; |
}; |
}; |
}; |
|
ðernet { |
pinctrl-names = "default"; |
pinctrl-0 = <&rgmii1_pins &mdio_pins>; |
|
port@5 { |
status = "okay"; |
phy-handle = <&phy5>; |
phy-mode = "rgmii"; |
}; |
|
mdio-bus { |
status = "okay"; |
|
phy5: ethernet-phy@5 { |
reg = <5>; |
phy-mode = "rgmii-rxid"; |
}; |
}; |
}; |
|
&gsw { |
mediatek,port4 = "ephy"; |
}; |
|
&wmac { |
ralink,mtd-eeprom = <&factory 0>; |
}; |
|
&pcie { |
status = "okay"; |
}; |
|
&pcie0 { |
wifi@0,0 { |
compatible = "pci0,0"; |
reg = <0x0000 0 0 0 0>; |
mediatek,mtd-eeprom = <&factory 0x8000>; |
ieee80211-freq-limit = <5000000 6000000>; |
}; |
}; |