/branches/18.06.1/target/linux/ramips/dts/U7628-01.dtsi/U7628-01.dtsi |
@@ -0,0 +1,139 @@ |
/* |
* BSD LICENSE |
* |
* Copyright(c) 2017 Kristian Evensen <kristian.evensen@gmail.com>. |
* Copyright(c) 2017 Piotr Dymacz <pepe2k@gmail.com>. |
* All rights reserved. |
* |
* Redistribution and use in source and binary forms, with or without |
* modification, are permitted provided that the following conditions |
* are met: |
* |
* * Redistributions of source code must retain the above copyright |
* notice, this list of conditions and the following disclaimer. |
* * Redistributions in binary form must reproduce the above copyright |
* notice, this list of conditions and the following disclaimer in |
* the documentation and/or other materials provided with the |
* distribution. |
* * Neither the name of Broadcom Corporation nor the names of its |
* contributors may be used to endorse or promote products derived |
* from this software without specific prior written permission. |
* |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR |
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, |
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY |
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
*/ |
|
#include "mt7628an.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
compatible = "unielec,u7628-01", "mediatek,mt7628an-soc"; |
|
aliases { |
led-boot = &led_power; |
led-failsafe = &led_power; |
led-running = &led_power; |
led-upgrade = &led_power; |
}; |
|
chosen { |
bootargs = "console=ttyS0,115200"; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <20>; |
reset { |
label = "reset"; |
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
led_power: power { |
label = "u7628-01:green:power"; |
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; |
}; |
|
wlan { |
label = "u7628-01:green:wlan"; |
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
}; |
|
wan { |
label = "u7628-01:green:wan"; |
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; |
}; |
|
lan1 { |
label = "u7628-01:green:lan1"; |
gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; |
}; |
|
lan2 { |
label = "u7628-01:green:lan2"; |
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; |
}; |
|
lan3 { |
label = "u7628-01:green:lan3"; |
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; |
}; |
|
lan4 { |
label = "u7628-01:green:lan4"; |
gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; |
}; |
|
usb { |
label = "u7628-01:green:usb"; |
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; |
trigger-sources = <&ohci_port1>, <&ehci_port1>; |
linux,default-trigger = "usbport"; |
}; |
}; |
}; |
|
&gpio0 { |
status = "okay"; |
}; |
|
&gpio1 { |
status = "okay"; |
}; |
|
&pcie { |
status = "okay"; |
}; |
|
ðernet { |
mtd-mac-address = <&factory 0x28>; |
}; |
|
&wmac { |
status = "okay"; |
ralink,mtd-eeprom = <&factory 0x0>; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "gpio", "p0led_an", "p1led_an", "p2led_an", "p3led_an", "p4led_an", "refclk", "wdt", "wled_an"; |
ralink,function = "gpio"; |
}; |
}; |
}; |