/branches/18.06.1/target/linux/ramips/dts/LR-25G001.dts |
@@ -0,0 +1,181 @@ |
/dts-v1/; |
|
#include "mt7620a.dtsi" |
|
#include <dt-bindings/gpio/gpio.h> |
#include <dt-bindings/input/input.h> |
|
/ { |
compatible = "lava,lr-25g001", "ralink,mt7620a-soc"; |
model = "LAVA LR-25G001"; |
|
aliases { |
led-boot = &led_status; |
led-failsafe = &led_status; |
led-running = &led_status; |
led-upgrade = &led_status; |
}; |
|
keys { |
compatible = "gpio-keys-polled"; |
poll-interval = <20>; |
|
wps { |
label = "wps"; |
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_WPS_BUTTON>; |
}; |
|
reset { |
label = "reset"; |
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; |
linux,code = <KEY_RESTART>; |
}; |
}; |
|
leds { |
compatible = "gpio-leds"; |
|
led_status: status { |
label = "lr-25g001:green:status"; |
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
}; |
|
wifi2g { |
label = "lr-25g001:green:wifi2g"; |
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
}; |
|
wifi5g { |
label = "lr-25g001:green:wifi5g"; |
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
}; |
}; |
|
gpio_export { |
compatible = "gpio-export"; |
#size-cells = <0>; |
|
usbpower { |
gpio-export,name = "usbpower"; |
gpio-export,output = <1>; |
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
}; |
}; |
}; |
|
&gpio0 { |
status = "okay"; |
}; |
|
&spi0 { |
status = "okay"; |
|
flash@0 { |
compatible = "jedec,spi-nor"; |
reg = <0>; |
spi-max-frequency = <10000000>; |
|
partitions { |
compatible = "fixed-partitions"; |
#address-cells = <1>; |
#size-cells = <1>; |
|
partition@0 { |
label = "jboot"; |
reg = <0x0 0x10000>; |
read-only; |
}; |
|
partition@10000 { |
compatible = "amit,jimage"; |
label = "firmware"; |
reg = <0x10000 0xfe0000>; |
}; |
|
config: partition@ff0000 { |
label = "config"; |
reg = <0xff0000 0x10000>; |
read-only; |
}; |
}; |
}; |
}; |
|
&ehci { |
status = "okay"; |
}; |
|
&ohci { |
status = "okay"; |
}; |
|
ðernet { |
status = "okay"; |
pinctrl-names = "default"; |
pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>; |
|
port@5 { |
status = "okay"; |
phy-mode = "rgmii"; |
mediatek,fixed-link = <1000 1 1 1>; |
}; |
|
mdio-bus { |
status = "okay"; |
mediatek,mdio-mode = <1>; |
|
phy0: ethernet-phy@0 { |
reg = <0>; |
phy-mode = "rgmii"; |
qca,ar8327-initvals = < |
0x04 0x87300000 /* PORT0 PAD MODE CTRL */ |
0x0c 0x00000000 /* PORT6 PAD MODE CTRL */ |
0x7c 0x0000007e /* PORT0_STATUS */ |
0x94 0x00000000 /* PORT6_STATUS */ |
>; |
}; |
|
phy1: ethernet-phy@1 { |
reg = <1>; |
phy-mode = "rgmii"; |
}; |
|
phy2: ethernet-phy@2 { |
reg = <2>; |
phy-mode = "rgmii"; |
}; |
|
phy3: ethernet-phy@3 { |
reg = <3>; |
phy-mode = "rgmii"; |
}; |
|
phy4: ethernet-phy@4 { |
reg = <4>; |
phy-mode = "rgmii"; |
}; |
}; |
}; |
|
&pcie { |
status = "okay"; |
}; |
|
&pcie0 { |
mt76x0e@0,0 { |
reg = <0x0000 0 0 0 0>; |
mtd-mac-address = <&config 0xe07e>; |
mtd-mac-address-increment = <(2)>; |
mediatek,mtd-eeprom = <&config 0xe08a>; |
}; |
}; |
|
&pinctrl { |
state_default: pinctrl0 { |
gpio { |
ralink,group = "uartf", "i2c"; |
ralink,function = "gpio"; |
}; |
}; |
}; |