OpenWrt
| /branches/18.06.1/target/linux/ramips/dts/GL-MT300N.dts |
|---|
| @@ -13,7 +13,7 @@ |
| bootargs = "console=ttyS0,115200"; |
| }; |
| leds { |
| gpio-leds { |
| compatible = "gpio-leds"; |
| wan { |
| @@ -30,10 +30,13 @@ |
| label = "gl-mt300n:wlan"; |
| gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| keys { |
| gpio-keys-polled { |
| compatible = "gpio-keys-polled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| poll-interval = <20>; |
| reset { |
| label = "reset"; |
| @@ -47,7 +50,7 @@ |
| linux,code = <BTN_0>; |
| }; |
| BTN_1 { |
| BTN_1 { |
| label = "BTN_1"; |
| gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; |
| linux,code = <BTN_1>; |
| @@ -66,7 +69,7 @@ |
| &gpio2 { |
| status = "okay"; |
| }; |
| &gpio3 { |
| status = "okay"; |
| }; |
| @@ -75,42 +78,37 @@ |
| status = "okay"; |
| m25p80@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <10000000>; |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| partition@0 { |
| label = "u-boot"; |
| reg = <0x0 0x30000>; |
| }; |
| partition@0 { |
| label = "u-boot"; |
| reg = <0x0 0x30000>; |
| }; |
| partition@30000 { |
| label = "u-boot-env"; |
| reg = <0x30000 0x10000>; |
| read-only; |
| }; |
| partition@30000 { |
| label = "u-boot-env"; |
| reg = <0x30000 0x10000>; |
| read-only; |
| }; |
| factory: partition@40000 { |
| label = "factory"; |
| reg = <0x40000 0x10000>; |
| read-only; |
| }; |
| factory: partition@40000 { |
| label = "factory"; |
| reg = <0x40000 0x10000>; |
| read-only; |
| }; |
| partition@50000 { |
| label = "firmware"; |
| reg = <0x50000 0xf80000>; |
| }; |
| partition@50000 { |
| compatible = "denx,uimage"; |
| label = "firmware"; |
| reg = <0x50000 0xf80000>; |
| }; |
| partition@ff0000 { |
| label = "art"; |
| reg = <0xff0000 0x10000>; |
| }; |
| partition@ff0000 { |
| label = "art"; |
| reg = <0xff0000 0x10000>; |
| }; |
| }; |
| }; |